Electric Co SI2200W 사용 설명서 - 페이지 16

{카테고리_이름} Electric Co SI2200W에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Electric Co SI2200W 18 페이지.

페이지 인쇄

1. Limpeza

- Never iron fabrics with stains since the heat of the appliance marks the stains on the

fabric, making them difficult to remove.

- It is recommended the selection of a lower temperature when use starch on the fabrics

and when iron without steam. The excessive heat burns the starches and forms yellow

stains.

- To avoid shinny patches on velvet fabrics, iron them only in one direction (the direction of

fibre).

- Many fabrics become easier to iron if they are not completely dry. For example, the silk

should be iron when still moist.

TROUBLESHOOTING

- During use, if any irregularities are detected on the appliance's operation, check the

below table to understand the causes and solutions to resolve them. If not possible, please

contact the Customer Support Line or the store where the appliance was bought.

Problem

Possible Cause

The temperature selector button

(J) is set to minimum.

The appliance is

turned on but

does not heat

up.

Problems with the wall socket.

The temperature selector button

The appliance

(J) was set to a too high

heats too much.

temperature for the fabric to be

ironed.

The water tank is empty or does

not have enough water.

The appliance

The steam control button (C) is

does not

turned off.

produce enough

or any steam at

all.

The appliance has not reached

the required temperature.

Solution / Hint

Set the temperature selector

button (J) to the intended

temperature.

Check if the wall socket is

damage and connect the

appliance to a wall socket in

good conditions.

Set the temperature selector

button (J) to a lower

temperature, more suitable for

the fabric to be ironed.

Fill the water tank. See the

instructions "Filling up the water

tank".

Set the steam output on button

iron.

Set the temperature selector

button (J) to the position marked

with the symbols "

" and "

and wait until the appliance

warms up.

The steam vents at the

soleplate (M) are clogged with

limestone.

You did not wait the

recommended period of time

between each pressing of the

No vertical

button (E).

steam boost

output.

The steam boost has been used

too often in a small period of

time.

Not enough pressure or air

inside the water tank.

The water spray

does not work.

The water tank has no water or

has an insufficient amount of it.

Limestone formation and

Limestone

minerals residues.

residues and

water drips

come out

through the

soleplate's vents

The appliance has not warmed

(M).

up enough.

The steam function is being

Water droplets

used and the appliance has not

on garments.

reached the necessary

temperature.

Use distilled water and a wood

toothpick to unclog the steam

vents in the soleplate (M).

Proceed to the self-cleaning to

remove limescale and minerals

accumulated. See the

instructions in "Self-cleaning

function."

Wait 1 minute between each

pressing of the button (E) and

then use this function again.

Never repeat this procedure

more than 3 consecutive times.

Wait about 1 minute before

using this function again.

Press repeatedly the spray

button (D).

Fill the water tank. See the

instructions in "Filling the water."

Proceed with the self-cleaning

function to remove lime scale

and minerals accumulated. See

the instructions in "Self-cleaning

function."

Set the temperature selector

button () to the position marked

with the symbols "

" and "

and wait until the appliance

warm up.

Set the temperature selector

button (J) to the position marked

with the symbols "

" and "

and wait until the appliance

warms up.

Reduce the steam output when

ironing at a low temperature.