Douglas Dynamics Fisher Minute Mount 2 XLS 50600 설치 지침 매뉴얼 - 페이지 2
{카테고리_이름} Douglas Dynamics Fisher Minute Mount 2 XLS 50600에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Douglas Dynamics Fisher Minute Mount 2 XLS 50600 17 페이지. Snowplow
페이지 인쇄50600, 50810
SAFETY DEFINITIONS
WARNING
Indicates a potentially hazardous situation
that, if not avoided, could result in death or
serious personal injury.
CAUTION
Indicates a potentially hazardous situation
that, if not avoided, may result in minor or
moderate injury. It may also be used to alert
against unsafe practices.
NOTE: Indicates a situation or action that can lead
to damage to your snowplow and vehicle or other
property. Other useful information can also be
described.
Instruction Label
Headgear
Jack
(fully raised)
Headlamp
Bracket
Pin Release
Handle (raised)
Stop
Jack
Jack
Lock
Handle
Pin Release
Attachment
Handle
Arm
(lowered)
Connecting
Jack
Pin
Jack
(lowered)
U.S Patents 4,999,935; 5,353,530; 5,420,480; 6,253,470; 6,944,978; RE 35,700;
CAN Patent 2,060,425; and other patents pending.
Read Owner's Manual For Complete Instructions
1. Place control in Lower/Float to put blade
down.
2. Pull and hold Jack Lock out. Jack will drop to
ground. Then pull Pin Release Handle away
from Stop and Jack Lock. Release Jack
Lock. Verify Jack is locked by trying to lift
Jack.
Lit. No. 50579, Rev. 02
1. Push
Pin Release
Handle down to pull out
Connecting Pins.
2. Drive vehicle slowly to engage
Pushplates into Attachment Arms.
3. Stand in front of blade. Fully raise Pin Release
Handle to release Connecting Pins.
4. Push Headgear toward vehicle to allow Connecting Pins
Pushplate
to fully engage Pushplates. If unable to push Headgear
from in front of blade, stand in front of Headgear on driver
side and push Headlamp Bracket.
5. Pull out Jack Lock. Push Pin Release Handle into Stop.
6. While holding Jack Lock out, use Jack Handle to raise
Jack fully. Release Jack Lock.
7. Attach all electrical connectors.
3. Stand in front of blade. While pushing Headgear toward
vehicle with left hand, push Pin Release Handle down to
disengage Connecting Pins. Make sure Connecting
Pins are fully retracted. If unable to push Headgear from
in front of blade, stand in front of Headgear on driver side
and push Headlamp Bracket.
4. Detach all electrical connectors.
WARNING/CAUTION AND INSTRUCTION
LABELS
Become familiar with and inform users about the
warning labels on the back of the blade and the
instruction label on the headgear.
NOTE: If labels are missing or cannot be read, see
your sales outlet.
Warning/Caution Label
LOWER BLADE WHEN VEHICLE IS PARKED.
DO NOT EXCEED GVWR OR GAWR INCLUDING BLADE
AND BALLAST.
REMOVE BLADE ASSEMBLY BEFORE PLACING
VEHICLE ON HOIST.
READ OWNER'S MANUAL BEFORE OPERATING OR
SERVICING SNOWPLOW.
TRANSPORT SPEED SHOULD NOT EXCEED 45 MPH.
FURTHER REDUCE SPEED UNDER ADVERSE TRAVEL
CONDITIONS.
PLOWING SPEED SHOULD NOT EXCEED 10 MPH.
SEE YOUR SALES OUTLET/WEB SITE FOR SPECIFIC
VEHICLE APPLICATION RECOMMENDATIONS.
27451
2
WARNING
CAUTION
59900
Multiple Pinch Points Label
XLS™ Blades Only
(both sides)
April 15, 2010