Douglas Dynamics WESTERN MVP PLUS 75300 설치 지침 매뉴얼 - 페이지 13

{카테고리_이름} Douglas Dynamics WESTERN MVP PLUS 75300에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Douglas Dynamics WESTERN MVP PLUS 75300 15 페이지. Snowplow

페이지 인쇄

OPERATIONAL TEST AND FINAL ADJUSTMENTS

VEHICLE LIGHTING CHECK

1. Verify the operation of all vehicle front lighting

prior to connecting the snowplow harness.

2. Check the operation of the snowplow lights with

snowplow mounted to vehicle and all harnesses

connected.

Turn signals and parking lamps

Parking lamps ON:

• Both vehicle and snowplow parking lamps

should be ON at the same time.

Driver-side turn signal ON:

• Both vehicle and snowplow driver‑side turn

signal lamps should flash at the same time.

Passenger-side turn signal ON:

• Both vehicle and snowplow passenger‑side

turn signal lamps should flash at the same time.

Headlamps

Move the vehicle headlamp switch to the

"ON" position. Connecting and disconnecting the

snowplow lighting harness plug should switch the

lights between vehicle and snowplow as follows:

Snowplow lighting harness DISCONNECTED:

• Vehicle headlamps should be ON.

• Snowplow headlamps should be OFF.

Snowplow lighting harness CONNECTED:

• Snowplow headlamps should be ON.

• Vehicle headlamps should be OFF.

The dimmer switch should toggle headlamps

between high and low beams. The high beam

indicator on the dash should light when headlamps

are placed in high beam.

Daytime Running Lamps (DRLs)

An operational check of the vehicle and snowplow

DRLs will depend on the vehicle model, vehicle

DRL system, and type of Isolation Module

installed. Due to the variations in the OEM DRL

systems and the different Isolation Module

options available, checking the functionality of the

snowplow DRLs will depend on the type of module

installed on the vehicle.

With the headlamp switch OFF, activate the

vehicle DRLs.

Lit. No. 43174, Rev. 04

Snowplow lighting harness DISCONNECTED:

• Vehicle DRLs should be ON.

• Snowplow headlamps should be OFF.

Snowplow lighting harness CONNECTED and

vehicle in DRL mode:

• Check snowplow DRL function per the type of

Isolation Module installed.

Refer to the Mechanic's Guide for information on

the Isolation Module DRL functions.

Joystick Control or CabCommand Control

The snowplow plugs do need to be connected to

the vehicle harness connectors. The control power

indicator light should light whenever the control

ON/OFF switch and the ignition (key) switch are

both in the "ON" position.

3. Connect all snowplow and vehicle harnesses.

Raise the snowplow and aim the snowplow

headlamps according to the Snowplow Headlamp

Beam Aiming Instructions included with the

headlamps, and any state or local regulations.

4. Check the aim of the vehicle headlamps with the

snowplow removed.

On 2‑plug electrical systems, plug covers

shall be used whenever snowplow is

disconnected. Vehicle battery cable is

12V unfused source.

5. When the snowplow is removed from the vehicle,

install plug covers on the vehicle battery cable

and lighting harness. Insert the snowplow battery

cable and lighting harness into the cable boot on

the snowplow.

OWNER'S MANUAL PACKET

If the completed snowplow will be delivered

immediately, the Owner's Manual should be reviewed

with and given to the purchaser according to the

snowplow checklist.

If the snowplow is completed prior to delivery to the

purchaser, attach the Owner's Manual packet to the

electrical cable of the cab control for safekeeping.

CAUTION

July 15, 2020