Asus RP-N12 빠른 시작 매뉴얼
{카테고리_이름} Asus RP-N12에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Asus RP-N12 2 페이지. Wireless-n300 range extender
Asus RP-N12에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (7 페이지), 빠른 시작 매뉴얼 (37 페이지)
페이지 인쇄
RP-N12
Wireless-N300 Range Extender
Quick Start Guide
Q10319
Second Edition
March 2015
Method One
Quick Setup with WPS (Wi-Fi Protected Setup)
For router/Access Point(AP) with WPS support
1
Power On
Place your RP-N12 near your router/AP and plug it to
a power outlet.
Wait until the Wi-Fi LED starts
to blink green.
3
Place in an ideal location
After placing your RP-N12 in an ideal location, RP-N12 connects to your router/AP in about one (1) minute.
NOTES:
• P lace your RP-N12 between your router/AP
and wireless device to get the best extender
performance.
• P lace your RP-N12 in a location where you can
get green Wi-Fi LED.
IMPORTANT!
• T o minimize interference, keep RP-N12 away from devices like cordless phones, Bluetooth devices and microwave ovens.
• W e recommend that you place your RP-N12 in open or spacious location.
Q1: What should I do if my router does not support WPS?
A1: You can use Method Two to set up RP-N12.
Q2: Why is that the Wi-Fi LED does not light up after completing Method
Two?
A2: You may have entered the wrong router SSID and password. Reset your RP-N12,
double check your router SSID/password, and set up RP-N12 again.
Q10319_RP-N12_QSG_Special_Europe.indd 1
2
Connect via WPS (Wi-Fi Protected Setup)
1. Press the WPS button on your Router/AP. 2. Press the WPS button on your RP-
NOTE: Ensure that your router/AP supports WPS. Otherwise, use Method TWO.
Frequently Asked Questions (FAQ)
Q3: Why is it that I cannot see the login page after entering http://
A3: Ensure that your computer is connected to the extender network only, and
Q4: How do I reset RP-N12?
A4: Using a pin, press the RESET button for about two (2) seconds. Wait for
N12.
Your RP-N12's wireless network name (SSID) changes
to your existing Wi-Fi network name, ending with
_RPT and shares your router/AP's Wireless Password.
repeater.asus.com in the browser?
set your computer to Obtain an IP address automatically.
about five (5) seconds until the Wi-Fi LED flashs red.
1. Power LED
On: RP-N12 is on
Off: RP-N12 is off
2. Ethernet LED
On: Device is connected to the
Ethernet port.
Off: Device is not connected to the
Ethernet port.
3. Wi-Fi LED
Green: RP-N12 provides the best
Wi-Fi extender performance.
Red: RP-N12 provides poor Wi-Fi
extender performance.
Off: RP-N12 is not connected to a
router/AP.
NOTE: Please refer to step 3 in Method
One for the best Wi-Fi performance.
The Wi-Fi LED flashs for
about two (2) minutes and
then turns solid green or
red. The color of the LED
indicates the Wi-Fi signal
strength.
Enjoy!
Reset
2015/4/13 15:26:27