Dover Triton 9610 설치 매뉴얼 - 페이지 2

{카테고리_이름} Dover Triton 9610에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dover Triton 9610 3 페이지. Dispensing mechanism
Dover Triton 9610에 대해서도 마찬가지입니다: 전환 매뉴얼 (4 페이지)

페이지 인쇄
Dover Triton 9610 설치 매뉴얼
Model 9610 Dispenser Mechanism Installation
PURPOSE
The following procedure assumes you are installing a
Model 9610 dispensing mechanism into a Model 9600
ATM chassis.
PARTS SUPPLIED
P
A
R
T
S
S
1
0
9
0
0
5
0 -
0
1
1
0
D
s i
p
e
n
1
2
2
0
0
0
0 -
0
4
0
0
C
r u
e r
n
c
1
2
2
0
0
0
0 -
0
4
0
1
C
r u
e r
n
c
1
2
2
0
0
0
0 -
0
4
0
2
C
r u
e r
n
c
S
c
e r
, w
4
0
2
0
5
4
0 -
0
0
4
9
n i
c
h
9 (
1
0
3
0
7
2
0 -
0
0
0
4
C
a
b
e l
C
S
c
e r
, w
1
0
2
3
0
1
0 -
0
0
0
4
W
a
s
h
r e
1
0
7
0
0
0
0 -
0
2
0
0
U
S
C /
a
n
*
C
a
s
s
t e
e t
n i
c
u l
d
e
d
n i
K
t i
w
l l i
U
, S
U
K
r o
C
a
n
a
d
. a
R
E
C
O
M
M
E
N
7
1 /
- 6
n i
c
h
1 (
1
m
m
)
W
e r
n
c
M
e
d
u i
m
P
h
l l i
p i
s
S
c
e r
w
r d
TRITON SYSTEMS, INC.
U
P
P
L
E I
D
s
r e
M
e
c
h
a
n
s i
m
y
C
a
s
s
t e
e t
-
U
S
*
y
C
a
s
s
t e
e t
-
C
a
n
a
d
a i
* n
y
C
a
s
s
t e
e t
-
U
K
*
P
a
n
H
e
a
d
P
h
l l i
p i
, s
#
8
3 -
, 2
/ 3
- 8
m
m
)
i l
, p
T
n i
n
r e
m
a
, n
R
u
b
b
r e
C
o
a
e t
d
#
8
3 -
, 2
H
e
x
N
t u
w
E /
t x
T
o
o
h t
a
d
a i
n
C
r u
e r
n
c
y
L
a
b
l e
d
e
p
e
n
d
u
p
o
n
a t
g r
t e
c
o
u
n
r t
: y
D
E
D
T
O
O
L
S
h
v i
r e
INSTALLATION PROCEDURE
1. Open the ATM control panel and ensure the power
switch (on the power supply panel) is set to the
OFF (0) position.
2. Unlock and open the security cabinet door. Extend
the slide tray fully. Set the 9610 dispenser onto the
tray. Turn the dispenser so that the rear of the unit
(where the power and data cable connectors are
located) may be accessed.
3. Locate the DC Power and EJ-to-Dispenser (Data)
cables. Connect the cables to the mating
connectors located on the back of the dispenser.
NOTE: Make sure the white strain clip on the
DC Power Cable is pointing down. Make sure
the thumbscrews on the EJ-to-Dispenser cable are
tightened.
Make sure the connector
on the dispenser DC
Power cable is
positioned as shown.
4. Turn the dispenser around with the cables facing
the back of the cabinet and align the tabs and holes
in the bottom of the dispenser with the mounting
holes in the tray. Attach the dispenser to the tray
using four included 3/8-inch (9 mm) Pan Head
Phillips Screws (two on each side).
EJ-to-Dispenser
Cable.
2