Combi BC-W31 설치 매뉴얼 - 페이지 2
{카테고리_이름} Combi BC-W31에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Combi BC-W31 2 페이지. Baby keep wa corner mounting kit
페이지 인쇄Baby Keep WA Corner Mounting Tools
Necessary Strength of Installation Fixtures
Install the Baby Keep in an area where reinforcement measures
strong enough to support the following conditions have been
taken. Failure to do so may result in collapse.
Wall:1,000N (100kgf) or more per place
623.5mm
204mm
Corner Mounting Kit Hardware
and Accessories
1
M6 Screws, 8
φ6 Flat washers,
2
2 big (diameter φ20),
2 small (diameter φ12)
φ4 Self-tapping screws, 4
3
4
Corner cover, 2
5
Braille sticker, 1
6
Installation Manual, 3
EN
CN
KR
Please prepare the following before installation:
• M8 Female type anchor bolts (for use with large holes), 4
*Use ALC-specific anchors for ALC installation
M6, M8, or M10 types
Spring
can be used
washers
Bolts
Washers
Corner Installation Instructions
1
Place a mark on the wall 545mm
above the floor.
Make an installation point
545mm
5
Attach the other corner cover to the
top part of the base.
Part is
included
3
* Hole positions are all center pitch (center-to center) dimensions.
2
Align the bottom points of the corner
fixtures to the areas marked on the wall. Once
four points have been marked on the wall, install
the anchor bolts.
115
115
Female type anchor bolts, 4
(
(
Use an M6, M8, or M10
female type anchor bolt.
*At least 40mm in length
510mm
510mm
545
560mm
560mm
mm
6
Attach the base to the corner fixture
connected to the wall.
Parts are
included
2
Parts are
included
1
Parts are
included
2
Parts are
included
1
6 holes
Holes in backboard
Bottom cover
as seen from
the front
2 holes
3
Fix the corner fixtures to the wall at
four mounting points.
Do not use small holes
Bolts
Spring washers
Washers
(
(
Use an M6, M8, or M10
female type anchor bolt.
Do not use small holes
7
Attach the head pad and bottom cover.
Head pad
(supplied with
Baby Keep)
Square holes
Back side
*The up arrow on the back
indicates which side is up.
Match the 6 tabs with the
corresponding square holes
on the backside to attach the
head pad.
Confirm that the guard works properly
by opening and closing several times.
CAUTION
The head pad tabs
will make a clicking
sound when correctly
attached. Note that
Screws, 2
the tabs may break if
incorrectly inserted.
Screw caps, 2
(supplied with
WARNING
Baby Keep)
4
Remove the bottom cover of the Baby
Keep WA (henceforth the base), and
mount the corner cover.
Bottom cover
Parts are
included
3
Corner cover
8
The stickers other than Corner sticker are
come with the product.
Guide stickers, 2
Usage instructions stickers
(supplied with
(supplied with Baby Keep)
Baby Keep)
5
Corner
sticker
Baille
sticker
Routine
inspection
sticker
Restroom entrance
Restroom stall
• Stickers must be placed in highly visible areas. Dangerous
actions such as indicated on the usage instructions sticker
may lead to injury or serious accidents.
• Thoroughly check the Baby Keep WA once it has been
installed. Refer to the Users Manual "Maintenance Inspec-
tion" section. Using the Baby Keep WA without completely
assembling it can lead to injury or serious accidents.
137916080 201225
(
1
)