Combi Lakumug Series 사용 설명서 - 페이지 4
{카테고리_이름} Combi Lakumug Series에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Combi Lakumug Series 4 페이지.
페이지 인쇄Common parts
Attaching the handle
●
CAUTION
Match the protruded
parts on the front of
the cup with the slots
The handle is not fixed on
●
the body of the cup. When
on the handle's ring
the adapter is removed, do
top.
not pick up the cup by
holding the handle.
Otherwise, the cup may fall
off and drink may spill. If it
is hot drink, scald may be
caused.
If the handle is not correctly
●
installed on the body of the
cup, the adapter cannot be
firmly fixed. As a result,
drink may leak.
About inner straw
Lakumug series has two types of inner straw. If the straw is not correctly installed, drink in the cup may not be
drunk off. As shown in the following figure, check the length of the inner straw and install the inner straw of
appropriate length.
When the straw is used on a standard cup (240ml)
When the first straw is used on a standard cup (240ml)
When the straw is used on a large cup (340ml)
First straw
The cup adopts a structure with a convex part. When the cap is opened
●
a little, you will hear a click sound. When you use the product, slowly
open the cap. To close the cap, press it downward until a click sound is
heard, which means the cap is locked.
How to assemble
① As shown in the figure,
install the straw and
air vent by pushing
them from inside
of the adapter.
Adapter
Straw
Air vent
② As shown in
the figure, insert
Drinking
the inner straw
spout
all the way until
it reaches
the
line.
Inner straw
Installing position
After the inner
※
of the inner straw
straw is inserted,
gently pull the
straw to ensure
Inner side of
that it cannot be
the adapter
pulled out.
③ Install the handle on the cup.
④ Close the cap and install the adapter on the cup. Screw up until
the protruding part match with the protruding part of the handle.
First cup
When you use the product, slowly open the cap.
●
To close the cap, press it downward until a click sound is heard
which means the cap is locked.
How to assemble
① As shown in the figure, install the drinking spout. Insert the spout
part into the adapter from the inner side and push it to outer side
with both hand. When insert, align the central part of the spout part
with the protruding part of the adapter.
※ When you push out the drinking spout, do not press the slit.
Cap
Slit
Adapter
Spout part
Drinking spout
Spout part
② Install the handle on the cup.
③ Close the cap and install the adapter on the cup. Screw up until
the protruding part match with the protruding part of the handle.
Straw
The cup adopts a structure with a convex part. When the cap is opened
●
a little, you will hear a click sound. When you use the product, slowly
open the cap. To close the cap, press it downward until a click sound is
heard, which means the cap is locked.
How to assemble
① As shown in the figure,
install the straw and
air vent by pushing
them from inside
of the adapter.
Adapter
Straw
② As shown in the
Air vent
figure, insert the
inner straw all the
Drinking spout
way until it reaches
its installation position.
※ After the inner straw is inserted,
gently pull the straw to ensure
that it cannot be pulled out.
③ Install the handle on the cup.
④ Close the cap and install the
adapter on the cup. Screw up until the protruding part match with
the protruding part of the handle.
Scale
The scale indicated on the cup is for reference only
and may be slightly different from actual volume.
Maximum marking
●
MAX
It is marked as MAX.
Standard cup...240ml
Large cup...340ml
Standard cup
How to disassemble
Remove the straw and air vent
by pushing it down from outside.
Cap
The edge should
completely come out.
CAUTION
Insert until
it reaches
When drink flows out from
●
the
line
the tip of the straw, see
page 14.
Inner straw
How to disassemble
As shown in the figure, press
the spout part of the drinking
spout inward from the left and
right to remove it.
※ When you remove the
drinking spout, be careful
not to press the slit.
Slit
Spout part
The edge should
completely come out.
How to disassemble
As shown in the figure, remove
the straw and air vent by
pushing them from outside.
Cap
The edge should
completely come out.
How to close the cap
Directly close the cap. Do not
Inner straw
touch the drinking spout of the
straw.
Installing position
of the inner straw
CAUTION
Inner side of
When drink flows out from
the adapter
●
the tip of the straw, see
page 14.
Care and storage
●
Wash the cup immediately after using. If the cup is left unused for long, bacteria may grow or the
drink color or odor may remain.
●
It is recommended to replace with new ones if the parts contaminated with color cannot be cleaned
even after washing or bleaching.
340ml
●
Excessive bleaching, disinfecting, boiling or microwave sterilizing may cause damage to the
240ml
product.
●
Damage may be caused to product from bleaching, chemical sterilizing, boiling or sterilizing using
a microwave oven particularly if done on a frequent basis.
●
If you boil the cup using little hot water or a small pot, the product may closely contact with the pot,
thus causing deformation.
Washing method
Disassemble the mug immediately after using, soak in
●
warm water, wash carefully using neutral detergent
for dishes and dry thoroughly.
Large cup
Carefully wash the drinking spout of the first straw and
●
straw and the inner straw using detergent for dishes,
and rinse off with water.
The slit of the first cup is prone to crack. Therefore, wash
●
it carefully. Do not put your finger in it or pull it to open.
If the air valve gets dirty, clean it gently with a toothpick.
●
Rinse the cap with strong running water if there is dirt on
●
the inner side.
When you use a dishwasher or dryer, keep the product
●
away from the hot air outlet because it will become hot.
When you use a dishwasher or dryer, use the relevant
●
neutral detergent. For details, follow instructions of the
detergent for dishwashers.
※Do not use commercial dishwashers or detergent for
commercial dishwashers.
Before the children can drink water with the straw
●
Start training
①
Hold the straw in the mouth...Water
of an appropriate amount flows out
When children hold the straw in their mouths,
the base of the straw is pressed and water of an
appropriate amount flows out from the tip of the
straw.
When training starts, an adult should put the
tip of the straw in the mouth of a child and watch
drinking.
※It is target. Let the child repeat continuously until the child can do it.
The sequence ①→② is not necessarily followed.
Guardians do not need to worry. Enjoy yourself while feeling the growth of children.
How does drink flow out from the first cup
●
Put spout part on the lower lip and hold the edge of
the spout part with lips. The slit can be opened to
let the water flow out only when children hold the
drinking spout in their mouths.
※ When using the cup for the
first time, children do not
know the tilt angle. Adults
should provide help.
Tilt angle (target tilt angle)
Adults should align the cup with the mouth of
children while checking the tilt angle.
Tilt check window
When drink flows out from the tip of the straw
When you give children warm drink or fill cold drink in the cup and place the cup for
●
some time, drink may flow out from the tip of the straw. Fully release pressure in
the cup. In addition, when you expand the air vent using fingers, drink may also
flow out from the air vent. Please be cautious.
If the cup is kept with the cap opened, drink may flow out from the straw due to
●
change of the surrounding environment. If you want to leave the cup for a while,
close the cap.
If you place the first straw and straw while the cap is
opened, drink may flow out from the straw due to
pressure difference caused by the temperature
difference between the inside and outside of the cup.
In this case, as shown in Figure B, hang the air vent
on the protruding part of the adapter side to open the
air valve to release pressure and prevent drink from
flowing out from the straw.
※If you overturn and carry the cup in the state shown
in Figure B, drink may spill out. Before handing
over the cup to children, be sure to restore the air vent to the normal state (as shown in Figure A).
※As shown in the illustration in "Caution" above, press the air vent with fingers to make it deform and
temporarily release pressure.
CAUTION
Disinfection and sterilization method
Sterilize in boiling water
●
When sterilizing in boiling water, use a large saucepan
filled with plenty of water boil for 2 to 3 minutes.
※Do not boil the cup for more than 3 minutes.
●
Disinfect and sterilize using chemicals
Use sterilizing agent for nursing supplies. For details,
follow instructions of the sterilizing agent. Depending on
the composition of the sterilizing agent, the silicone parts
may turn white and the printed color of the product may
fade.
●
Sterilizing using a microwave oven
Use a sterilization tool for nursing supplies. For details,
follow instructions for each tool.
Storage
Keep the mug out of the reach of the children as
●
the small parts may pose a chocking hazard.
Learn drinking water with the straw
②
Shrink lips at the base of the straw and suck
out a small amount of water.
After a child can proficiently drink water with the
"first straw" , use the "straw" . The tip of the
straw is expanded to form a shape that makes
it easy for children to keep the straw in the mouth
and drink water.
●
finger into the slit of the drinking spout,
the slit may become wide or the drinking
spout cracks, causing leakage.
●
in the slit of the drinking spout, leakage
may occur because the slit is always in
the open state.
●
If a drinking spout is used for a long time,
leakage may occur due to loss of elasticity,
expansion of the slit and crack.
●
cap is open, drink may leak.
Incline to make the drink reach
the line.
CAUTION
Projection of the
adapter side
Shrink lips...Suck water
CAUTION
When using the product, if children put a
Slit
If foreign objects such as food are blocked
The drinking spout is consumable part.
If the cup is placed horizontally while the
Release pressure
The air
valve is
Air vent
opened.
Normal
Air valve opened