Follett HCD710AHT 빠른 시작 매뉴얼 - 페이지 8
{카테고리_이름} Follett HCD710AHT에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Follett HCD710AHT 8 페이지.
페이지 인쇄
6 – Horizon Elite ice tube runs - specifier guidelines
Long tube runs for RIDE remote ice delivery equipment
beverage
dispenser
minimum of
6.00" (15.24 cm)
turn/corner
ice transport tube –
1 3/16" OD,
2 1/8" OD with insulation
Ice production – Horizon Elite 710 series, air-cooled 60 Hz
Inlet water
temperature
F (C)
60 (16)
70 (21)
50 (10)
787 (357)
759 (345)
60 (16)
750 (341)
702 (319)
70 (21)
707 (321)
681 (309)
677 (307)
629 (286)
80 (27)
90 (32)
642 (291)
600 (272)
Ice production – Horizon Elite 710 series, air-cooled 50 Hz
Inlet water
temperature
60 (16)
70 (21)
F (C)
50 (10)
664 (301)
617 (280)
60 (16)
645 (293)
601 (272)
626 284)
582 (264)
70 (21)
80 (27)
588 (267)
544 (247)
90 (32)
557 (252)
519 (235)
ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S. Environmental Protection Agency.
Agion is a registered trademark of Sciessent LLC.
HORIZON ELITE, ICE•DEVICE, MICRO CHEWBLET, SAFECLEAN PLUS, SANISPONGE, SYMPHONY PLUS and VISION are trademarks of Follett Products, LLC.
CHEWBLET, FOLLETT and RIDE are registered trademarks of Follett Products, LLC, registered in the US.
Follett reserves the right to change specifications at any time without obligation. Certifications may vary depending on country of origin.
Self-contained 710 series ice machine
8225-202205 | © Follett Products, LLC
support
maximum
straps
2' (60.9 cm)
radius
transport tube slope
(toward ice machine)
1/4"
(2 cm per meter)
Ambient air temperature F (C)
80 (27)
90 (32)
100 (38)
705 (320)
639 (290)
603 (274)
666 (302)
624 (283)
570 (259)
636 (289)
586 (266)
542 (246)
611 (277)
559 (254)
518 (235)
580 (263)
539 (245)
497 (226)
Ambient air temperature F (C)
80 (27)
90 (32)
100 (38)
576 (261)
538 (244)
500 (227)
560 (254)
521 (236)
481 (218)
544 (247)
506 (229)
464 (210)
512 (232)
481 (218)
389 (176)
487 (221)
455 (207)
328 (149)
wall-mounted
ice machine
1'
801 Church Lane | Easton, PA 18040, USA
1.800.523.9361 | 1.610.252.7301 | follettice.com
Important specifier notes
1. 75' (22.9 m) maximum ice transport
tube run.
2. Tubing routing bends must have a
6.00" (15.24 cm) radius or larger.
3. Dips and traps are not allowed. If not
supported from underneath, secure
insulated ice transport tube at least
every 2' (60.9 cm) to prevent drips
and traps.
4. Relative humidity levels above 80%
in areas where the ice machine or ice
transport tube is located may produce
excessive condensation that will cause
water damage.
5. Contact factory for recommendations
on running tubing through a decorative
soffit or chase.