Cardax Prox 125 설치 참고 사항 - 페이지 4
{카테고리_이름} Cardax Prox 125에 대한 설치 참고 사항을 온라인으로 검색하거나 PDF를 다운로드하세요. Cardax Prox 125 10 페이지.
페이지 인쇄Connecting to the URI
The Prox 125 reader can connect to either a Cardax IV or CardaxFT URI.
Use the cable terminating tool to connect the cables to the socket as described in the
following sections.
Pin number 4 of the Prox 125 connector feeds into the cable terminating tool first.
The pin numbers are marked on the connector.
Connecting to the CardaxFT URI
Connect the cables to the socket as shown.
Connect the Prox 125 connector to either the P1 or P2 plug on the CardaxFT URI. Refer
to the CardaxFT URI component layout diagram, below, for the location of the plugs.
P3
Keypad
pin 1 = Row1
pin 2 = Row 2
P2
pin 3 = Row 3
Non-CardaxFT
pin 4 = Row 4
pin 5 = Column1
Reader 2
pin 6 = Column2
pin 1 = 5/12 V power
pin 7 = Column3
pin 2 = DataA
pin 8 = Ground
pin 3 = DataB
pin 4 = Card detect
pin 5 = LED output
pin 6 = Beeper output
pin 7 = Ground
P2
P1
P1
Non-CardaxFT
Reader 1
pin 1 = 5/12 V power
pin 2 = DataA
pin 3 = DataB
pin 4 = Card detect
pin 5 = LED output
pin 6 = Beeper output
pin 7 = Ground
4
Prox 125 Connector
Black
4
Blue
3
White
2
Red
1
F1
13.6 V Input Fuse
Rating = 500mA
P6
13.6 V ± 15%out
pin 1 = 13.6 V ± 15%
pin 2 = Ground 3A fused
F2
13.6 V Output Fuse
Rating = 3A
D19
JP2
D20
D15
D6
D5
R7
D4
Q2
D3
D2
P8
2
D1
1
(c)1999 PEC(New Zealand) Ltd
P8
Diagnostic port
CardaxFT Universal Reader Interface
Plug P1 or P2
D10
Comms LED
flashing = communicating with
FT Controller
D10
E
U19
T1
D22
D13
D11
5V
12V
JP1
D17
Q7
D21
D18
10
SW1
9
REV[A][B][C]
22825V2 Assy 22826
SW1
Unit address
Set unit number
GND
OUTPUTS
OUTPUTS
DET
COMMS
COMMS
5/12V
P5
Power & Comms
pins 1 & 2 = RS485
pin 3 = 13.6 V ± 15%
pin 4 = 0V
JP1
Reader Voltage select
= 5V
D12
= 12V
D16
D17
D21
and
NC NO
Relay state indicators
COIL
LED on = Energised
LED off = De-energised
COMM
D14
P7
Q41
NC NO
Relay Outputs
COIL
RLY2
pin 1 = R1 Normally closed
pin 2 = R1 Normally open
pin 3 = R1 Common
COMM
Q26
pin 4 = R2 Normally closed
R53
D23
R50
pin 5 = R2 Normally open
Q27
R54
D24
pin 6 = R2 Common
R51
Q28
R55
pin 7 = Ground
D25
R52
Q29
R79
D26
R94
R80
Q30
D27
R95
D18
R81
D28
Q31
R96
Run LED
P4
Balanced Inputs
pin 1 = Input1
pin 2 = Input 2
pin 3 = Input 3
pin 4 = Input 4
pin 5 = Input 5
pin 6 = Input 6
pin 7 = Ground
Part number 3E0000 R3
(200mA total)
(1A total)
April 2002