AMSEC FS149E5LP 사용 설명서 및 보증 - 페이지 3

{카테고리_이름} AMSEC FS149E5LP에 대한 사용 설명서 및 보증을 온라인으로 검색하거나 PDF를 다운로드하세요. AMSEC FS149E5LP 6 페이지.

OPERATING INSTRUCTIONS FOR THE ESL5-LP ELECTRONIC SAFE LOCK

Your AMSEC ESL5-LP Electronic Safe Lock has a Factory Combination of C-1-2-3-4-5-6-#

To open the lock, simply press the "C" key to clear and wake up the electronics. Now press the keys

of the combination one at a time and finish with the "#" key. If the combination keyed is correct, the

lock will cycle open for three (3) seconds. During this 3 second period, turn the handle or knob to the

unlocked position and pull the door open.

You may change your combination any time you like, and as many times as you like. Once your

safe is installed, you must change the combination to a number sequence other than the Factory

Combination of 1-2-3-4-5-6 to insure the safety of your valuables.

Here are a few things to remember:

a. With each keystroke the keypad lights will flash off and a chirp will be heard, unless Stealth Mode is

on, then no sounds are emitted during lock opening.

b. If 4 (four) incorrect combinations are entered, the lock will go into a "Penalty Lockout" for 15 minutes

to prevent trial and error manipulation attempts at opening the lock. The keypad will flash once

every 5 seconds during the penalty period. If you press any key during the lockout period, the

keypad will flash with a chirp 8 times rapidly to indicate the lockout condition.

c. Before keying the combination, be sure that the handle of the safe is in the fully locked position to

allow the lock to open freely.

d. If the lock fails to open or acts strange, replace the battery with a good quality fresh 9 volt alkaline

battery. To replace the battery, simply turn the keypad housing counter-clockwise to the stop and

pull it away from the base. Un-snap the old battery and clip on the new one. Position the battery it

in the pocket of the housing and replace the keypad, watching that the wires fold neatly inside and

are not pinched. You should replace your battery once a year to prevent corrosion damage from

leakage.

e. During the input sequence, if you make a mistake, you can press "C" to clear the previous input and

start over again.

f. The ESL5-LP uses a fixed length 6 (six) digit combination.

g. Use only your fingers to key the combination. Sharp objects will result in damage which is not

covered by warranty.

h. If at any time during opening, or combination changing, the unit is left without input for 10 (ten)

seconds, it returns to a resting condition. If this occurs during a combination change, the Old

Combination is retained.

i. At any time during opening or combination changing the unit will register the first 5 digits of the

combination into the "buffer" that receives input. The 6th digit will be the last numeric key pressed.

For example, if your press C-1-2-3-4-5-7-4-5-2-7-6-# the program recognizes only the C-1-2-3-4-5-6-

# input. The last numeric key pressed continues to replace the one prior until the "#" key is pressed

to indicate completion. This is a security feature that allows you to baffle an on-looker that may be

trying to memorize your combination.

Quiet Mode –Silent Operation

The ESL5-LP Lock provides a Stealth Mode you can program so the Beeper remains silent during

normal lock opening operation. To turn Stealth Mode ON (silent) or OFF (beeping):

ON: Press C-# (short warble tone), then 8-0-# (short warble), then 1-# (long warble).

OFF: Press C-# (short warble tone), then 8-0-# (short warble), then 0-# (long warble).