AMSEC TF5517E5 중요 작동 지침 - 페이지 3

{카테고리_이름} AMSEC TF5517E5에 대한 중요 작동 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. AMSEC TF5517E5 6 페이지. Dv series gun safes with esl5 electronic lock

페이지 인쇄

2. If the combination keyed is incorrect, the unit responds with 4 short beeps (called the bad combo tone) and

returns to rest. The combination change routine is aborted and the old combination is retained. This also

causes a count up for Penalty Lockout.

c. Now key the first pass with the New 6 digit combination followed by a "#" key. Again, the "C" key may be used to

clear an error in keying at any time.

1. If the combination input is 6 digits in length, another short good combo tone is sounded. Proceed to "d. "

2. If the combination keyed is not 6 digits long, the unit responds with 4 short beeps (bad combo tone) and

returns to rest. The combination change routine is aborted and the old combination is retained.

d. Now key the second (verify) pass with the New 6 digit combination followed by a "#" key. As before, the "C" key

may be used to clear an error in keying at any time.

1. If the combination input matched the first pass, a long good combo tone is sounded. The new combination

replaces the old combination in permanent memory and the unit returns to a resting condition. Proceed to "e. "

2. If the combination keyed does not match the first pass, the unit responds with the bad combo tone and

returns to rest. The combination change routine is aborted and the old combination is retained.

e. test your new combination several times prior to closing and locking the safe.

Operating instructiOns fOr the DV652 safe DOOr

Before operating the DV652 safe for the first time, remove the two (2) tray clamping socket head cap screws located in

the back of the safe. These screws can be removed using the supplied hex L key (Allen wrench).

After following the operating instructions for the ESL5 lock, (operating instructions 4305296), move the vault door

operating lever (located above the digital lock) to the right to release and drop the vault door down. The sliding

drawer can now be extended out of the vault.

After returning the sliding drawer back into the vault, the vault door can now be returned to the closed position.

While holding the door in the closed position, move the operating lever to the left to relock the vault.

DV652 instaLLatiOn instructiOns

anchOr kit (part #1825075)

Your Defense Vault has been furnished with anchor holes and the necessary hardware to secure to the floor using this

prescribed method.

Use the supplied hardware listed and drill the appropriate hole size and depth for the bolt size supplied.

item no.

cOncrete fLOOr instructiOns:

1. Place the Defense Vault in the desired location.

2. Open the Vault door, and extend the roll-out drawer.

3. Remove the hole plugs on the top of the vault and using a pencil, trace the holes in the bottom of the vault to mark

the hole locations.

4. Move the Defense Vault and drill (4) ½" diameter x 2" deep holes.

5. Clean the holes and drop (1) Lag Expansion Shield into each hole.

6. Place the Defense Vault back over the holes, insert the Lag Bolts and tighten down the bolts.

WOOD fLOOr instructiOns:

1. Place the Defense Vault in the desired location.

2. Open the Vault door, and extend the roll-out drawer

3. Remove the hole plugs on the top of the vault and using a pencil, trace the holes in the bottom of the vault to mark

the hole locations.

4. Move the Defense Vault and drill (4) 9/32" diameter x 1-3/4 deep holes.

5. Place the Defense Vault back over the holes, insert the Lag Bolts and tighten down the bolts.

Qty

part no.

2665005

244-0001

Description

3/8" Lag Expansion Shield

3/8" x 1-½" long Lag Bolt