Electrolux # 설치 지침 매뉴얼 - 페이지 9

{카테고리_이름} Electrolux #에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Electrolux # 21 페이지. Over the range microwave oven
Electrolux #에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (8 페이지), 사용 및 관리 매뉴얼 (20 페이지), 사용 및 관리 매뉴얼 (36 페이지), 사용 및 관리 매뉴얼 (24 페이지), 사용 및 관리 매뉴얼 (38 페이지), 레시피 북 (17 페이지), 지침 책자 (12 페이지), 사용 및 관리 매뉴얼 (20 페이지), 지침서 (16 페이지), 지침서 (12 페이지), 소개 매뉴얼 (16 페이지), 사용자 설명서 (11 페이지), 사용 및 관리 매뉴얼 (26 페이지), 사용 및 관리 매뉴얼 (38 페이지), 소유자 매뉴얼 (9 페이지), 사용 및 관리 매뉴얼 (16 페이지), 사용 및 관리 매뉴얼 (16 페이지), 소유자 매뉴얼 (16 페이지), 사용 및 관리 매뉴얼 (16 페이지), 서비스 매뉴얼 (49 페이지)

페이지 인쇄
Electrolux # 설치 지침 매뉴얼
30" GAS RANGE INSTALLATION INSTRUCTIONS

Important Safety Warning

To reduce the risk of tipping of the range, the range
must be secured to the floor by the properly installed
anti-tip bracket and screws packed with the range. These
parts are located in a plastic bag in the oven. 30" Range
has one bracket. Failure to install the bracket will allow
the range to tip over if excessive weight is placed on
an open door or if a child climbs upon it. Serious injury
might result from spilled hot liquids or from the range
itself.
Follow the instructions below to install the anti-tip bracket.
If range is ever moved to a different location, the anti-tip
bracket must also be moved and installed with the range.
Tools Required:
5/16" (8 mm) Nut driver or Flat Head Screwdriver
Adjustable Wrench
Electric Drill
3/16" (4.8 mm) Diameter Drill Bit
3/16" (4.8 mm) Diameter Masonry Drill Bit (if installing in
concrete)

Anti-Tip Bracket Installation

1. The anti-tip bracket must be install on the right or the
left side at back of the range.
2. The anti-tip bracket supports are attached to the floor
at the back. When fastening to the floor, be sure that
screws do not penetrate electrical wiring or plumbing.
The screws provided will work in either wood or
concrete.
3. Unfold paper template and place it flat on the floor
with the back and side edges positioned exactly where
the back and sides of range will be located when
installed. (Use the diagram in figure 13 to locate
bracket if template is not available.)
l l
W a
B
A
A
B
C e n
l l
W a
t e r
L i n e
Figure 13
30" range: Install the anti-tip bracket on the right or left side.
4. Mark on the floor the location of the mounting holes
shown on the template (right and left position). For
easier installation, 3/16" (4.8 mm) diameter pilot holes
1/2" (1.3 cm) deep can be drilled into the floor.
5. Remove template and place bracket on floor (see
figure 13). Line up holes in bracket with marks
on floor and attach the bracket using the screws
provided. Brackets must be secured to solid floor. If
attaching to concrete floor, first drill 3/16" (4.8 mm)
dia. pilot holes using a masonry drill bit.
6. Level range if necessary, by adjusting the 4 leveling
legs with an adjustable wrench. Loosen the screw
which fixes the decorative leg and lift it to reach the
leveling leg. Turn the leveling leg counterclockwise
to raise the range or clockwise to lower the range
(see Figure 14). Replace the decorative legs at your
convenience.
7. Before sliding the range to its final position; take note
of the serial and model numbers for future reference.
Slide range into place making sure rear leg is trapped
by the bracket. Range may need to be shifted slightly
to one side as it is being pushed back to allow rear leg
to align with bracket.
8. After installation, visually verify that the anti-tip
brackets are engaged.
Leveling
Leg
Raise
Lower
30" Range 11 5/16 (28.7 cm)
9
Decorative
Leg Screw
Figure 14
A
B
2 1/2 (6.4 cm)