Electrolux # 서비스 매뉴얼 - 페이지 17

{카테고리_이름} Electrolux #에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Electrolux # 49 페이지. Over the range microwave oven
Electrolux #에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (8 페이지), 사용 및 관리 매뉴얼 (20 페이지), 사용 및 관리 매뉴얼 (36 페이지), 사용 및 관리 매뉴얼 (24 페이지), 사용 및 관리 매뉴얼 (38 페이지), 레시피 북 (17 페이지), 지침 책자 (12 페이지), 사용 및 관리 매뉴얼 (20 페이지), 지침서 (16 페이지), 지침서 (12 페이지), 소개 매뉴얼 (16 페이지), 사용자 설명서 (11 페이지), 사용 및 관리 매뉴얼 (26 페이지), 사용 및 관리 매뉴얼 (38 페이지), 소유자 매뉴얼 (9 페이지), 사용 및 관리 매뉴얼 (16 페이지), 사용 및 관리 매뉴얼 (16 페이지), 설치 지침 매뉴얼 (21 페이지), 소유자 매뉴얼 (16 페이지), 사용 및 관리 매뉴얼 (16 페이지)

Electrolux # 서비스 매뉴얼
PROCEDURE
LETTER
(HIGH VOLTAGES ARE PRESENT AT THE HIGH VOLTAGE TERMINAL, SO DO NOT ATTEMPT TO
MEASURE THE FILAMENT AND HIGH VOLTAGE.)
C
HIGH VOLTAGE RECTIFIER TEST
. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the rectifier from the circuit. Using the highest ohm scale of the meter, read the resistance
across the terminals and observe, reverse the leads to the rectifier terminals and observe meter
reading. If a short is indicated in both directions, or if an infinite resistance is read in both directions,
the rectifier is probably defective and should be replaced.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: Be sure to use an ohmmeter that will supply a forward bias voltage of more than 6.3
volts.
D
HIGH VOLTAGE CAPACITOR TEST
. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. If the capacitor is open, no high voltage will be available to the magnetron. isconnect input leads
and check for short or open between the terminals using an ohmmeter.
Checking with a high ohm scale, if the high voltage capacitor is normal, the meter will indicate
continuity for a short time and should indicate an open circuit once the capacitor is charged. If the
above is not the case, check the capacitor with an ohmmeter to see if it is shorted between either
of the terminals and case. If it is shorted, replace the capacitor.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
E
CAVITY THERMAL CUT-OUT TEST
. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. A continuity check across the thermal cut-out terminals should indicate a closed circuit unless the
temperature of the thermal cut-out reaches approximately 293
An open thermal cut-out indicates overheating of the oven, exchange the oven thermal cut-out and
check inside of oven cavity and for improper setting of cooking time or operation of control unit.
Check for restricted air flow through the vent holes of the oven cavity, especially the cooling fan and
air guide.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
MAGNETRON TEMPERATURE FUSE TEST
. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. A continuity check across the magnetron temperature fuse terminals should indicate a closed circuit
unless the temperature of the magnetron temperature fuse reaches approximately 302
An open magnetron temperature fuse indicates overheating of the magnetron. Check for restricted
air flow to the magnetron, especially the cooling fan air guide.
TEST PROCEDURES
COMPONENT TEST
7
F(45
C).
O
O
O
F(50
GLMV169GSB
GLMV169GBB
GLMV169GQB
PLMVZ169GCB/C
O
C).