Electrolux # 서비스 매뉴얼 - 페이지 34

{카테고리_이름} Electrolux #에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Electrolux # 49 페이지. Over the range microwave oven
Electrolux #에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (8 페이지), 사용 및 관리 매뉴얼 (20 페이지), 사용 및 관리 매뉴얼 (36 페이지), 사용 및 관리 매뉴얼 (24 페이지), 사용 및 관리 매뉴얼 (38 페이지), 레시피 북 (17 페이지), 지침 책자 (12 페이지), 사용 및 관리 매뉴얼 (20 페이지), 지침서 (16 페이지), 지침서 (12 페이지), 소개 매뉴얼 (16 페이지), 사용자 설명서 (11 페이지), 사용 및 관리 매뉴얼 (26 페이지), 사용 및 관리 매뉴얼 (38 페이지), 소유자 매뉴얼 (9 페이지), 사용 및 관리 매뉴얼 (16 페이지), 사용 및 관리 매뉴얼 (16 페이지), 설치 지침 매뉴얼 (21 페이지), 소유자 매뉴얼 (16 페이지), 사용 및 관리 매뉴얼 (16 페이지)

Electrolux # 서비스 매뉴얼
GLMV169GSB
GLMV169GBB
GLMV169GQB
PLMVZ169GCB/C

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE

Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may
result in severe, possibly fatal, electric shock.
(Example)
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness
etc..
WARNING:
Avoid possible exposure to microwave energy. Please follow the instructions below before operat-
ing the oven.
. Disconnect the power supply cord.
2. Visually check the door and cavity face plate for damage
(dents, cracks, signs of arcing etc.).
Carry out any remedial work that is necessary before
operating the oven.
Do not operate the oven if any of the following conditions
exist;
. Door does not close firmly.
2. Door hinge, support or latch hook is damaged.
3. The door gasket or seal is damaged.
4. The door is bent or warped.
To prevent an electric shock, take the following pre-
cautions.
. Before wiring,
) Disconnect the power supply cord.
2) Open the door block it open.
3) Discharge the high voltage capacitor and wait for 60
seconds.
2. Don't let the wire leads touch to the followiong parts;
) High voltage parts:
Magnetron, High voltage transformer, High voltage
capacitor and High voltage rectifier assembly.
2) Hot parts:
Oven lamp, Magnetron, High voltage transformer and
Oven cavity.
Please refer to 'OVEN PARTS, CABINET PARTS, CONTROL PANAL PARTS, DOOR PARTS', when carrying out any of
the following removal procedures:
THE FOLLOWING ADJUSTMENTS OR COMPONENT REPLACEMENT CAN BE PERFORMED
. Hood lamps, sockets and grease filter.
2. Oven lamp, base cover and hood lamp glass
assembly.
3. Turntable motor.
. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove the three (3) screw holding the hood exhaust
louver to the oven cavity.
4. Pull the hood exhaust louver from the oven cavity by
pushing the right and left tabs of the hood exhaust
louver
WARNING AGAINST HIGH VOLTAGE:
WARNING FOR WIRING
WITHOUT REMOVING THE OVEN FROM THE WALL
HOOD EXHAUST LOUVER REMOVAL
5. There are defective parts in the door interlock
system.
6. There are defective parts in the microwave generating
and transmission assembly.
7. There is visible damage to the oven.
Do not operate the oven:
. Without the RF gasket (Magnetron).
2. If the wave guide or oven cavity are not intact.
3. If the door is not closed.
4. If the outer case (cabinet) is not fitted.
3) Sharp edge:
Bottom plate, Oven cavity, Waveguide flange,
Chassis support and other metallic plate.
4) Movable parts (to prevent a fault)
Fan blade, Fan motor, Switch, Switch lever, Open
button.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector until its pin is locked
and make sure that the wire leads do not come off
even if the wire leads are pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
4. Hood exhaust louver.
5. Control panel assembly or components
6. Stirrer cover and stirrer fan.
34
Push
Hood exhaust
louver
Tab (left )
Push
Tab (right)