Electrolux Built-In Dishwasher 지침서 - 페이지 9

{카테고리_이름} Electrolux Built-In Dishwasher에 대한 지침서을 온라인으로 검색하거나 PDF를 다운로드하세요. Electrolux Built-In Dishwasher 15 페이지. Built-in oven
Electrolux Built-In Dishwasher에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (36 페이지), 사용 및 관리 매뉴얼 (44 페이지), 설치 지침 매뉴얼 (28 페이지), 사용 및 관리 매뉴얼 (28 페이지), 사용 및 관리 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (27 페이지), 사용 및 관리 매뉴얼 (12 페이지), 사용 및 관리 매뉴얼 (22 페이지), 팁 및 레시피 (36 페이지), 사용 설명서 (18 페이지), 오워 매뉴얼 (21 페이지), 오워 매뉴얼 (13 페이지), 소유자 매뉴얼 (29 페이지), 사용자 설명서 (27 페이지), 지침서 (17 페이지), 지침서 (18 페이지), 지침서 (27 페이지), 지침서 (18 페이지), 서비스 매뉴얼 (50 페이지)

페이지 인쇄

Instructions for the installer

The instructions given below are

designed specifically for a qualified

installer and should aid him or her to

perform all installation, adjustment,

and maintenance operations with

absolute precision and in compliance

with all current legislation and

regulations. We strongly recommend

that all operations for the installation

of your cooker be carryed out by

Qualified Personnel in accordance

with existing rules and regulations.

Electrical connection

Prior to making the electrical connection,

make sure that:

— the protection fuse and the domestic

wiring system are suitable to carry the

total electric load of the oven (see rating

plate);

— your domestic wiring system has an

efficient earth connection in compliance

with rules and laws in force;

— the wall socket or the omnipole switch

used for the electrical connection can

easily be reached after the oven is built

in.

This appliance is delivered without an

electric supply cable, therefore, you will have

to fit to it a supply cable with standard plug,

suitable for the total electric load shown on

the rating plate. The plug is to be inserted

into a suitable wall socket. If you require a

direct connection to the electric network

(mains), it will be necessary to fit between

the appliance and the mains an omnipole

switch, with a minimum gap between

contacts of 3 mm, suitable for the required

load and in compliance with rules in force.

The green & yellow ground wire must not be

interrupted by the switch and it should be 2-

3 cm. longer than the other cables. The

supply cable must in all cases be laid out in

such a way as to ensure that it does not

reach at any given point a temperature 50°C

higher than the ambient temperature.

Suitable power supply cables are the

following types, considering the respective

necessary section of cable: H07 RN-F, H05

RN-F, H05 RR-F, H05 VV-F, H05 V2V2-F

(T90), H05 BB-F.

Connecting the terminal board

The appliance incorporates an easily

accessible 6-pole terminal board whose

jumpers (bridges) are already pre-set for

operation on 400V tri-phase with neutral wire

(Fig. 6). In case a different mains voltage is

present, the jumpers on the terminal board

must be rearranged as shown in the diagram

(Fig.7). The ground cable must be connected

FO 0330

Fig. 6

230V 3~

230V 1~

400V 2N~

400V 3N~

Fig. 7

FO 0584

1 2 3 4 5

L3 PE

1 2 3 4 5

L1 L2

1 2 3 4 5

L1 L2 L3 N