Bosch 300 Series 설치 매뉴얼 - 페이지 11

{카테고리_이름} Bosch 300 Series에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 300 Series 36 페이지. Built-in wall ovens
Bosch 300 Series에 대해서도 마찬가지입니다: 사용 설명서 지침 (40 페이지), 사용자 설명서 (21 페이지), 설치 매뉴얼 (6 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 설명서/설치 지침 (40 페이지), 사용 설명서 (50 페이지), 빠른 시작 및 안전 매뉴얼 (7 페이지), 설치 매뉴얼 (28 페이지), 빠른 시작 매뉴얼 (7 페이지), 사용 및 관리 매뉴얼 (32 페이지), 빠른 시작 및 안전 매뉴얼 (7 페이지), 서비스 매뉴얼 (36 페이지), 빠른 시작 및 안전 매뉴얼 (13 페이지)

페이지 인쇄
Bosch 300 Series 설치 매뉴얼
Confirm that the plate is properly centered and level.
5.
Securely tighten all screws, including the fifth wood
6.
screw in the bottom area of the mounting plate.
Attaching the mounting plate (wall stud at one corner
hole)
Insert the bolts and the wood screws into the mounting
1.
plate through the holes designated.
Attach toggle wings from the back of the mounting
2.
plate onto each bolt. Leave enough space for toggle
wings to go through the wall and to open.
Place the mounting plate against the wall and make
3.
sure tabs are touching the bottom of the cabinet or the
level line (see "Aligning the mounting plate").
Push the bolts through the drywall and finger tighten
4.
the bolts to make sure toggle wings have opened
against drywall.
Confirm that the plate is properly centered and level.
5.
Securely tighten all screws and bolts.
6.
Attaching the mounting plate (wall studs at both corner
holes)
Insert the wood screws into the mounting plate
1.
through the holes designated.
Place the mounting plate against the wall and make
2.
sure tabs are touching the bottom of the cabinet or the
level line (see "Aligning the mounting plate").
Confirm that the plate is properly centered and level.
3.
Securely tighten all screws.
4.

Adapting microwave blower

This microwave is shipped assembled for Room Venting
Installation. The blower unit is already in place and must
not to be adapted.
Adapting microwave blower for roof venting
Remove and save the screws holding the blower
1.
motor and the blower plate. Lift up the blower plate
and put it aside.
Carefully pull out the blower unit and rotate 90º so that
2.
fan blade openings are facing out the top of the
microwave.
Place the blower unit back into the opening.
3.
CAUTION
9
Do not pull or stretch the blower unit wiring. Make
sure the wires are not pinched, and that they are
properly secured.
Replace the blower plate and secure with the screws
4.
removed in step 1.
Attach the exhaust adapter to the top of the blower
5.
plate by sliding it into the guides. Push in securely until
it is in the locking tabs. Make sure the damper hinge
swings freely.
11