Bosch Ascenta SHE5AM02UC 시작하기
{카테고리_이름} Bosch Ascenta SHE5AM02UC에 대한 시작하기을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch Ascenta SHE5AM02UC 2 페이지. Quick reference instructions
Bosch Ascenta SHE5AM02UC에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (21 페이지), 에너지 매뉴얼 (2 페이지), 수리 지침 (50 페이지), 수리 지침 (27 페이지)
![Bosch Ascenta SHE5AM02UC 시작하기](/uploads/products/server2/1327861/1327861.jpg)
GETTING STARTED WITH YOUR NEW DISHWASHER
STEP 1 - AddInG rInse AGenT
FOR PROPER DRYING ALWAYS USE RINSE AGENT
detergent
rinse Agent
Compartment
Compartment
STEP 2 - AddInG deTerGenT
Opening the cover
•
Push dark gray button
STEP 3 - To sTArT THe dIsHwAsHer
Exposed Front Controls
1) Close the door
2) Turn on
3) Select a cycle
*If unit does not fill with water, ensure that incoming water supply is operational.
STEP 4 - wHen THe CyCle Is CoMPleTe
When is the Cycle Complete?
Depending on model you can tell when your unit has completed the cycle in one of the following ways. Please refer to your use and Care manual for
complete details.
• Countdown display at < 0 >
• Cycle completion signal sounds (tone adjustable)
Note that on most models you must turn the unit off (and then on again) before you can begin a new cycle.
Canceling a cycle
To cancel or change a cycle on hidden top control models, open the dishwasher
door far enough to expose the control buttons. Press and hold "start" button for
three seconds until "active" light stops flashing. Close the door and wait until
the dishwasher completes the cycle (approximately 1 minute). Open the door
and press the ON/OFF button. You may now begin a new cycle. For exposed
front control models, Press and hold "start" button for three seconds. Wait until
the dishwasher completes the cycle (approximately 1 minute). Open the door
and press the ON/OFF button. You may now begin a new cycle. Beware of hot
water splash-out.
Run Time
To save energy, this dishwasher has a Smart Control that automatically
adjusts the cycle based on soil loads and incoming water temperature. The
Smart Control makes decisions that can cause the cycle time and water
usage to adjust intermittently, and suddenly change mid-cycle. The cycle
times listed in the Use and Care manual are based on normal soil loads and
120°F incoming water and will vary based on your actual conditions.
AlwAys reAd your use And CAre MAnuAl For deTAIled InsTruCTIons And IMPorTAnT sAFeTy noTICes.
even if your detergent already contains it.
•
use fresh powdered detergent
for best results
3 TBS MAX
•
2 TBS (25 ML)
1 tablespoon will clean most
1 TBS (15 ML)
loads
•
3 tablespoons Max, do not
overfill
•
W hen using detergent tabs, lay
them flat to avoid contact with
the cover
Add detergent
4) Press start
•
Add rinse Agent when
the light on the control
panel illuminates
•
Lift tab to open
2) Turn on
• Clean light illuminates
• Cycle indicator light that shines on floor goes out
To contact customer service
open dishwasher door to
locate the label on right side.
There you will find:
Program progress and rinsing sounds
Cleaning/Final Rinse
Alternating sounds
Start
•
Closing the cover
•
•
Push rear of cover down
slide closed
firmly until you hear the
Hidden Top Controls
1) Open the door
4) Press start
3) Select a cycle
• Model Number
• Serial Number (FD#########)
• Toll Free Customer Service Phone Number
No sounds
9000266264 Rev. C• 12/07
To add rinse Agent
pour
in the oval
ClICK
5) Close the
door to start
Dry
End