Bosch DISHWASHER 사용 설명서 - 페이지 22

{카테고리_이름} Bosch DISHWASHER에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch DISHWASHER 25 페이지. Dishwasher bosch
Bosch DISHWASHER에 대해서도 마찬가지입니다: 사용 설명서 지침 (30 페이지), 설치 지침 매뉴얼 (34 페이지), 사용 설명서 (30 페이지), 사용 설명서 (28 페이지), 사용 설명서 (30 페이지), 사용 설명서 (38 페이지), 사용 설명서 (42 페이지), 사용 설명서 지침 (32 페이지), 사용 설명서 지침 (36 페이지), 사용 설명서 지침 (30 페이지), 사용 설명서 (24 페이지), 사용 설명서 지침 (26 페이지), 사용 설명서 지침 (40 페이지), 사용 설명서 지침 (28 페이지), 사용 설명서 지침 (29 페이지), 사용 설명서 (28 페이지), 사용 설명서 (28 페이지), 사용 설명서 지침 (28 페이지), 설치 지침 매뉴얼 (50 페이지), 설치 지침 매뉴얼 (20 페이지), 운영 지침 (24 페이지), 작동 지침 (36 페이지), 사용 설명서 (46 페이지), 사용 설명서 지침 (31 페이지)

페이지 인쇄
Bosch DISHWASHER 사용 설명서
aus

Fresh water connection

– Connect the fresh-water connection to
the tap according to the installation
instructions with the enclosed parts.
Ensure that the fresh-water connection
is not kinked, crushed or twisted.
– When replacing the appliance, always
use a new water supply hose.
Water pressure:
at least 0.05 MPa (0.5 bar), maximum
1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing valve
ahead.
Inlet rate:
minimum 10 litres/minute
Water temperature:
for cold water connection only.

Electrical connection

– Connect the appliance to an alternating
current only, ranging from 220 V to
240 V and 50 Hz or 60 Hz via
a correctly installed socket with
protective earth conductor. See rating
plate for required fusing 9*.
– The socket must be near the appliance
and freely accessible following
installation.
– The connection may be modified by
technicians only.
– A power cord extension may be
purchased from customer service only.
– Use only a residual current operated
circuit-breaker which features the
symbol ‚. Only this extension
guarantees compliance with the
currently valid regulations.
– The appliance features a water
damage protection system. Please
note the system will not function
unless the power supply is connected.
22

Removing the appliance

Also observe the sequence of worksteps
here.
– Disconnect the appliance from the
power supply.
– Turn off the water supply.
– Disconnect the waste water and fresh
water connections.
– Loosen the fastening screws under the
worktop.
– If fitted, remove the base panel.
– Pull out the appliance, carefully pulling
the hose behind.

Transportation

Empty the dishwasher and secure loose
parts.
Drain the appliance according to the
following steps:
– Turn on the tap.
– Open the door.
– Switch on ON/OFF switch (. The
displays of the last selected
programme light up.
– Select programme with the highest
temperature.
The expected programme duration is
indicated on the numerical display
8.
– Press START button h.
– Close the door.
Programme sequence starts.
– Open door after approx. 4 minutes.
– Press START button h until :
indicated on the digital display.
– Close the door.
– Open door after approx. 1 minute.
The numerical display indicates :
– Switch the appliance off ( and turn
the tap off.
Transport appliance upright only.
(This prevents residual water from running
into the machine control and damaging
the programme sequence.)
is
.