Bosch FAP-OC 500Series 서비스 매뉴얼 - 페이지 17

{카테고리_이름} Bosch FAP-OC 500Series에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch FAP-OC 500Series 41 페이지. Built-in wall ovens
Bosch FAP-OC 500Series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (21 페이지), 사용 설명서 지침 (40 페이지), 설치 매뉴얼 (6 페이지), 제품 정보 (40 페이지), 설치 매뉴얼 (28 페이지), 사용자 설명서 (48 페이지), 사용자 설명서 (48 페이지), 설치 매뉴얼 (28 페이지), 사용 및 관리 매뉴얼 (44 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 설명서/설치 지침 (40 페이지), 빠른 참조 매뉴얼 (4 페이지), 사용 및 관리 매뉴얼 (27 페이지), 설치 매뉴얼 (24 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 매뉴얼 (24 페이지), 설치 매뉴얼 (28 페이지), 사용 및 관리 매뉴얼 (21 페이지), 설치 매뉴얼 (32 페이지), 서비스 매뉴얼 (36 페이지), 설치 매뉴얼 (32 페이지), 빠른 시작 및 안전 매뉴얼 (13 페이지)

페이지 인쇄

58300000202181 ARA EN B

3. Hold the latch hook and slide the latch assembly back and a

little to the left to disengage it from the small support bracket

that sits directly behind it, then pull the latch forward.

Figure 18 Door latch/motor assembly and rear support bracket

4. Disconnect the wires.

5. Install the new latch/motor assembly, reconnecting the wires

and engaging the latch correctly with the latch support bracket.

6. Position the latch plate with the curved corners at the bottom,

and reinsert screws.

7. Restore power and test operation.

6.3 Oven High Temperature Cutout (HTC)

The resettable HTC is a normally closed 12VDC thermal switch that is

used to detect over-temperature conditions within the oven. It has a

connector that will interrupt the double line break (DLB) relay coil

voltage supply if the temperature reaches 185°C/365°F. When the

HTC switch opens, it breaks the line to the double line break (DLB)

relays, cutting off power to the elements.

With the latch plate removed, the HTC and the bracket it's mounted

on are visible to the left of the door latch/motor assembly. Figure 19

shows the HTC and bracket, but note that this view is looking from the

rear of the oven towards the front, beneath the top plenum.

This material is intended f or the sole use of BSH authorized persons and may contain conf idential and proprietary inf ormation. Any unauthorized rev iew, use, copy ing, disclosure, or distribution in any f ormat is prohibited.

Novemb er 2018

Figure 19 HTC and mounting bracket

6.3.1 Resetting and Replacing the HTC

Always troubleshoot a tripped HTC to determine the underlying cause

of the interruption.

To reset the HTC...



The HTC switch should only be reset once or twice before being

replaced. The switch weakens each time it trips, so it will become

easier and easier for the switch to trip during high-temperature cycles

(i.e., Self-clean) if it has weakened over time.

To remove the HTC from the front, a right-angled screwdriver will be

needed....*

1901 Main St ▪ Suite 600 ▪ Irvine, CA 92614

Service Manual for Bosch 500 Series Built-in Wall Ovens

1. Remove power to the oven.

2. insert a flat blade screwdriver through one of the vent slots,

and depress the red reset button.

3. Restore power and test operation.

NOTICE

1. Remove power to the oven.

Page 17 of 41

800 944-2904