Bosch 2 설치 및 활용 매뉴얼 - 페이지 16

{카테고리_이름} Bosch 2에 대한 설치 및 활용 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 2 18 페이지. Mini blender
Bosch 2에 대해서도 마찬가지입니다: 빠른 설치 매뉴얼 (16 페이지), 원본 사용 설명서 (13 페이지), 원본 사용 설명서 (22 페이지), 사용 설명서 (32 페이지), 사용자 설명서 (28 페이지), 사용자 설명서 및 설치 지침 (16 페이지), 사용 설명서 (42 페이지), 사용 설명서 (8 페이지), 사용 설명서 (8 페이지), 사용 설명서 (12 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (9 페이지), 사용 설명서 및 설치 지침 (36 페이지), 사용자 설명서 및 설치 지침 (48 페이지), 사용 설명서 (26 페이지), 빠른 참조 매뉴얼 (2 페이지), 사용자 설명서 및 설치 지침 (24 페이지), 사용 설명서 (42 페이지), 사용 정보 (28 페이지), 사용자 설명서 (40 페이지), 사용자 설명서 및 설치 지침 (35 페이지), 사용자 설명서 (24 페이지)

Bosch 2 설치 및 활용 매뉴얼
BTEXACT_bu_3609929A44_t.fm Seite 15 Montag, 5. September 2005 2:12 14
close the LED work area lamp 26 can now be placed
in any desired position. Take care not to damage the
cable of the LED work area lamp and slide it into the
cavity 31 intended for it in the housing shell without

6 MAINTENANCE AND SERVICE

Maintenance
Remove the battery from the power tool before
adjustments are made to the tool, accessories
are changed or the tool is stored. This safety
measure prevents the unintentional switching on of
the power tool.
Should the tool fail in spite of careful manufacturing
and testing procedures, have the repairs performed
by an authorized customer service center for Bosch
power tools.
For inquiries and spare parts ordering, please include
the 10-place article number on the nameplate of the
tool.
After approx. 150 hours of operation, the gearbox is
to be cleaned for the first time and then after every
300 hours of operation. After each cleaning, it should
be lubricated with special gearbox grease.
The moving parts of the coupling are to be lubricated
every approx. 100000 screwing fasteners with a few
drops of SAE 10/SAE 20 motor oil. The sliding and
rolling parts are to be lubricated with Molycote
grease. Check the setting of the coupling after lubri-
cating.
Lubrication
Lubricant:
Special gearbox grease 225 ml
3 605 430 009
Molycote grease
SAE 10/SAE 20 motor oil
Have maintenance and repair work performed
only by qualified specialists. In this manner, it can
be ensured that the safety of the tool is maintained.
Any Bosch customer service center can perform this
work quickly and reliably.
Dispose of lubricants and cleaning agents in an
environment-friendly manner. Comply with the
legal regulations.
3 609 929 A44 • (05.09) T
kinking. Enclose the LED work area lamp 26 again
with the two housing shells of the LED holder 15.
Press the spring ring 30 and the marking ring 19 back
to their initial positions.
Accessories
You can obtain NiCd battery packs and voltage
adapters for voltages of 9.6 V, 12.0 V, and 14.4 V,
Screw heads, constant voltage regulator 4EXACT,
and access point EXAConnecT at your specialty
dealer.
Bosch offers various charging units for the batter-
ies:
AL 15 FC 2498
ML 60-4
For the selection of the suitable charger, assistance
is provided by the authorized Bosch customer serv-
ice center for power tools or your dealer.
Information about the complete quality accessory
program can be found on the Internet at
www.bosch-pt.com and
www.boschproductiontools.com or at your dealer.
Service
Robert Bosch GmbH is responsible for the delivery of
the tool in accordance with the sales contract within
the framework of the legal/country-specific regula-
tions. For claims with respect to the tool, please con-
tact the following location:
Fax . . . . . . . . . . . . . . . . . . . . +49 (711) 7 58 24 36
www.boschproductiontools.com
English–15