Bosch FAP-OC 500Series 사용자 설명서 - 페이지 16

{카테고리_이름} Bosch FAP-OC 500Series에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch FAP-OC 500Series 48 페이지. Built-in wall ovens
Bosch FAP-OC 500Series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (21 페이지), 사용 설명서 지침 (40 페이지), 설치 매뉴얼 (6 페이지), 제품 정보 (40 페이지), 설치 매뉴얼 (28 페이지), 사용자 설명서 (48 페이지), 설치 매뉴얼 (28 페이지), 사용 및 관리 매뉴얼 (44 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 설명서/설치 지침 (40 페이지), 빠른 참조 매뉴얼 (4 페이지), 사용 및 관리 매뉴얼 (27 페이지), 설치 매뉴얼 (24 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 매뉴얼 (24 페이지), 설치 매뉴얼 (28 페이지), 서비스 매뉴얼 (41 페이지), 사용 및 관리 매뉴얼 (21 페이지), 설치 매뉴얼 (32 페이지), 서비스 매뉴얼 (36 페이지), 설치 매뉴얼 (32 페이지), 빠른 시작 및 안전 매뉴얼 (13 페이지)

Bosch FAP-OC 500Series 사용자 설명서
en-us Troubleshooting
8 Troubleshooting

Troubleshooting

You can eliminate minor issues on your appliance your-
Troubleshooting
self. Please read the information on eliminating issues be-
fore contacting Customer Service. This may avoid unnec-
essary repair costs.
WARNING
Improper repairs are dangerous.
Only authorized service providers should repair the ap-
pliance.
Issue
None
All displays flash
is flashing in the cooking zone
displays.
and the power level flash alter-
nately. A signal tone sounds.
and audible signal
/
+
/
and cooking zones not
heating
/
16
Cause and troubleshooting
The power supply has been disconnected.
Check whether the lighting in your kitchen or other appliances in the room are
working.
The appliance has not been connected as shown in the circuit diagram.
Disconnect the appliance from the power supply.
1.
Make sure the appliance has been connected as shown in the circuit diagram.
2.
There is an electronics fault
If the fault cannot be eliminated, call Customer Service.
Controls are wet or objects are lying on top of them.
Dry the controls or remove the object.
There is an electronics fault
Briefly cover the control panel with your hand to acknowledge the fault.
The electronics have overheated. The corresponding cooking zone has been
switched off.
Wait until the electronics have cooled down sufficiently.
1.
Touch any control element.
2.
a When error message disappears, the electronics have cooled down sufficiently.
You can continue to cook.
The electronics have overheated. All cooking zones have switched off.
Wait until the electronics have cooled down sufficiently.
1.
Touch any control element.
2.
a When error message disappears, the electronics have cooled down sufficiently.
You can continue to cook.
There is hot cookware near the control panel. The electronics are at risk of over-
heating.
Remove the cookware from the control panel.
a You can continue to cook.
There is hot cookware near the control panel. The cooking zone has switched off to
protect the electronics.
Remove the cookware from the control panel.
1.
Wait a few seconds.
2.
Touch any control element.
3.
a When error message disappears, the electronics have cooled down sufficiently.
You can continue to cook.
The cooking zone has overheated. It has switched off to protect the work surface.
Wait until the electronics have cooled down sufficiently.
1.
Switch the cooking zone back on.
2.
a You can continue to cook.
The cooking zone has been operating continuously for an extended period of time
without interaction. The automatic time limitation has been triggered.
Touch any control element.
a You can set the cooking zone and continue to cook.
The supply voltage is incorrect. It is outside the normal operating range.
Contact your electrical utility provider.
If the appliance has an issue, call Customer Support.
WARNING
Improper repairs are dangerous.
Repairs to the appliance should only be performed by
authorized service providers.
Only original spare parts may be used to repair the ap-
pliance.