Bosch FAP-OC 500Series 서비스 매뉴얼 - 페이지 11

{카테고리_이름} Bosch FAP-OC 500Series에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch FAP-OC 500Series 36 페이지. Built-in wall ovens
Bosch FAP-OC 500Series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (21 페이지), 사용 설명서 지침 (40 페이지), 설치 매뉴얼 (6 페이지), 제품 정보 (40 페이지), 설치 매뉴얼 (28 페이지), 사용자 설명서 (48 페이지), 사용자 설명서 (48 페이지), 설치 매뉴얼 (28 페이지), 사용 및 관리 매뉴얼 (44 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 설명서/설치 지침 (40 페이지), 빠른 참조 매뉴얼 (4 페이지), 사용 및 관리 매뉴얼 (27 페이지), 설치 매뉴얼 (24 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 매뉴얼 (24 페이지), 설치 매뉴얼 (28 페이지), 서비스 매뉴얼 (41 페이지), 사용 및 관리 매뉴얼 (21 페이지), 설치 매뉴얼 (32 페이지), 설치 매뉴얼 (32 페이지), 빠른 시작 및 안전 매뉴얼 (13 페이지)

페이지 인쇄

3. Pull the halogen bulb straight out from its socket.

4. Using a clean, dry cloth, insert the new bulb.

5. Reinsert the bottom of the glass cover (smooth side out) into

the bottom clip, and firmly push the top of the cover into the

upper clip until it snaps into place.

6. Restore power to the unit.

4.3.1.2

Halogen Side Lamp (Horizontal-style)

1. Remove racks and rack support.

2. Slide tip of flat-blade screwdriver between fixing clip and lamp

housing, while supporting lens cover along bottom edge.

Holder

clip

Figure 10 Horizontal-style side lamp

3. Gently twist screwdriver to loosen the lens cover.

4. Remove cover and fixing clip.

5. Grasp halogen bulb and pull it straight out from its socket.

6. Using a clean, dry cloth, insert new bulb into socket.

7. Reinsert lens cover into the holder clip and gently push back

until fixing clip snaps into place.

8. Restore power to the unit.

4.3.1.3

Halogen Ceiling Lamp and Incandescent Cavity Lamp

1. Unscrew glass cover.

2. Pull halogen bulb straight out of its socket, or unscrew

appliance bulb.

3. Using a clean, dry cloth, insert the new bulb.

4. Replace the glass cover.

5. Restore power to the unit.

Slide screwdriver

between fixing clip

and lamp housing.

Figure 11 Round halogen ceiling lamp (L); traditional lamp with 40W or 25W appliance

bulb (R).

4.4

High Temperature Cutout (HTC)

The HTC is a normally closed switch which will interrupt the relay

supply voltage in the event of a high temperature event caused by a

malfunctioning control module.

The HTC is located in the plenum, behind and to the left of the MDL.

Although it cannot be easily removed or replaced, a screwdriver can

be used to reach the reset button located on the top center of the HTC

after the latch plate has been removed.

4.5

Convection Fan and Ring Element

All models except the HBL33/HBN33 and the lower cavity of the

HBL56/HBN56 and HBL35/HBN35 models, which have a thermal

oven cavity, are configured with convection capabilities in the upper

and/or lower ovens. The HBL34/HBN34 and HBL35/HBN35 models

have a convection fan only, and the remaining models with convection

cavities have both a convection fan and a convection (also called a

rd"

"ring" or "3

) element, which gives the ovens true (or genuine

European) convection capability.

Depending on the cooking mode selected, the fan may be used, with

or without the ring element, to circulate heat evenly throughout the

cavity in various cooking modes.

Service Manual for Bosch Built-in Wall Ovens

Page 11 of 36