Draper Access FIT Series 지침 - 페이지 2

{카테고리_이름} Draper Access FIT Series에 대한 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper Access FIT Series 4 페이지. Electric projection screen 220v
Draper Access FIT Series에 대해서도 마찬가지입니다: 설치 및 작동 지침 (8 페이지)

페이지 인쇄

Access Fit

Motorized Roller/Fabric Installation

Please note: When ordering a motor with internal Low Voltage Controller, if

the case ships separate from the "guts," the case includes the 25' cable and

special low voltage switch.

The bottom access panel must be removed first.

The motor end mounting bracket has a metal

bracketwith snap ring for accepting motor head.

Back out the two set screws in bracket until they are

flush with top side of bracket.

To engage the motor end bracket flange above the

two channels in the top of the screen housing, rotate

the bracket approximately 45° counterclockwise to

allow the top surface of the motor bracket to rest flat

against the top inside of the housing.

Rotating the bracket clockwise until it is engaged

with the channels, slide it along the length of the

housing against the electrical junction box.

Engage idler end bracket

(rectangular

mounting pad)

in the same manner

asmotor end bracket and slide it toward

the opposite end of the screen housing.

Do not tighten set screws on this

bracket until the roller/fabric assembly is

installed, and centered in case.

Note: Step 6 requires two people to perform safely.

Locate the black washer and retaining clips attached to the

instruction sheet.

Raise the roller/fabric assembly up into the screen housing

and engage the head of the motor completely into the motor

mounting bracket, making sure the limit switch adjusting

knobs are visible from the bottom of the screen housing

(see fig.

8). If snap ring is provided, make sure the snap ring

engages with the motor. If retaining clip is provided instead,

install to lock motor end in place.

While supporting the idler end of the roller, slide the idler end

mounting bracket toward the roller. Insert the roller pin into the

nylon bushing on the idler end mounting bracket.

The roller idler pin needs to go through the idler bracket far

enough to allow the washer and retaining clip to be reinstalled

on the pin.

CAUTION: Failure to replace the washer and retaining clip could result in

the separation of the roller from the brackets.

The roller/fabric assembly and roller brackets may need to be slid left or right in

the mounting channel of case to center fabric within screen case.

Securely tighten the set screws on roller mounting brackets.

Connect the electrical plug from the motor to the mating socket on the junction box.

Reinstall the bottom access panel as previously described.

Motorized Roller/Fabric Removal

Reverse the instructions above "Motorized Roller/Fabric Installation" for

removal of the unit.

Operation

When screen is first operated, be cautious! Cycle unit down and up several

times to confirm satisfactory operation. Be prepared to cut POWER if

necessary.

110-120V SINGLE STATION CONTROL: 3-position UP-OFF-DOWN switch permits

operation to be stopped at any point. Factory adjusted limit switches automatically

stop screen when fully down or fully up.

110-120V MULTIPLE STATION CONTROL: Switches are similar in appearance

to 110-120V Single Station Control. Screen stops when switch is released and

may be restarted in either direction. Factory adjusted limit switches stop screen

automatically when fully up or fully down.

24V CONTROL: Three-button UP-STOP-DOWN switches stop at any point desired,

operate in any sequence. Factory adjusted limit switches automatically stop screen

when fully up or fully down.

110-120V & 12V VIDEO INTERFACE CONTROL: Allows screen to be controlled

by trigger signal—when the signal comes on, the screen descends automatically.

KEY OPERATED SWITCHING: Optionally available with this unit. The key-operated

power supply switch controls power to the screen and switches. When it is "off",

the switches will not operate screen. Key may be removed from the switch in either

"on" or "off" position.

RS232 / ETHERNET: Serial communication and network communication optionally

available.

(Pg 1, Fig.

4).

Figure 6

Motor roller

assembly

Washer

Retaining

clip

Idler end roller

mounting bracket

Motor End

Set Screws

Mounting

Bracket

Motor End

Retaining Clip

Figure 7

Tab-Tension Adjustment Procedure

Draper's Tab-Tensioning System is factory-

set, and under normal circumstances will

not require field adjustment. If, however, you

notice wrinkles, waves or other indications

that the tensioning cables need to be

adjusted, follow the procedure below.

Determine which side requires

adjustment.

Secure dowel with one hand.

Using Phillips-head screwdriver,

depress spring-loaded adjustment

screw and slowly turn CLOCKWISE

TO INCREASE tension, or COUNTER-

CLOCKWISE TO RELEASE tension.

The screw adjusts in 60° turn

increments. Adjust only one increment

If problem is not corrected, leave screen in position for 24 hours to allow

surface material to stretch into position.

If problem still is not corrected, repeat steps 2 and 3.

Limit Adjustments (Standard/Quiet Motors)

Please Note: Screen limits are factory set for optimum performance of the

screen. A procedure is outlined below for minor tweaks, but any adjustment of

these limits may negatively affect the flatness of the screen surface and could

also void the warranty. Please check with Draper prior to resetting screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in "off" position before adjusting limit

switches. The motor limit screws are normally located on the audience left of

screen roller.

Please Note: If Access Fit E/V is "Right Hand Motor" or "Waterfall", the WHITE/

DOWN (I) and YELLOW/UP (II) limit screws are reversed. See graphic below.

"Down" Limit Adjustment

To Reduce Screen Drop

Raise screen surface about 1' above desired setting and turn off.

Turn the WHITE/DOWN

(I)

limit screw clockwise

revolution).

Test by running screen down and repeat steps 1 and 2 until desired position is

reached.

To Increase Screen Drop

Run screen to the down limit.

With the down switch on, turn the WHITE/DOWN

clockwise

(3 screw turns = ½ roller revolution)

Test by running screen up about 1' and back down to new down limit.

Repeat steps 2 and 3 until desired position is reached.

"Up" Limit Adjustment

Screen is Running Too Far Up:

Lower screen surface about 1' below desired setting and turn off.

Turn YELLOW/UP

(II)

limit screw clockwise

revolution).

Test by running screen up.

Repeat steps 1 through 3 until desired position is reached.

Screen Needs to Run Up More

1 Run screen down about 1' and turn off.

With the up switch on, turn the YELLOW/UP

(3 screw turns = ½ roller

revolution).

Repeat steps 1 and 2 until desired position is reached.

Figure 9

CAUTION: Do NOT

allow the dowel to wrap

up over the roller when

Motor

the screen is running up!

End

This could damage the

screen.

Standard Roll

page 2 of 4

Figure 8

END OF

DOWEL

PUSH & TURN

COUNTER-CLOCKWISE

CLOCKWISE

to RELEASE TENSION

to INCREASE TENSION

(60° turn)

at a time.

(three screw turns = ½ roller

(I)

limit screw counter-

to increase drop.

(3 screw turns = ½ roller

(II)

limit screw counterclockwise

Audience

Side

Audience

Side

Motor

End

Waterfall Roll

Reverse Roll

Standard/Reverse Roll

Waterfall Roll

Left hand motor

White Socket—Down

White Socket—Up

Yellow Socket—Up

Yellow Socket—Down

Right hand motor

White Socket—Up

White Socket—Down

Yellow Socket—Down

Yellow Socket—Up

Audience

Side