Draper Access/Series M 설치 및 운영 지침 - 페이지 2

{카테고리_이름} Draper Access/Series M에 대한 설치 및 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper Access/Series M 2 페이지. Draper access/series m projection screen

페이지 인쇄
Draper Access/Series M 설치 및 운영 지침
Access/Series M by Draper
(Continued from Page 1)
Install the retaining clip on the spear, locking spear and bracket together.
While supporting the idler end of the roller, slide the idler end mounting
bracket toward the roller. Insert the roller pin into the nylon bushing on the
idler end mounting bracket.
The roller idler pin needs to go through the idler bracket far enough to allow
the washer and retaining clip to be reinstalled on the pin. Failure to replace
the washer and retaining clip as shown could result in the separation of the
roller from the brackets.
Securely tighten the four set screws on the idler end mounting bracket.
Reinstall the bottom access panel as previously described.
Spring Roller/Fabric Removal
Reverse the instructions above "Spring Roller/Fabric Installation" for removal
of the unit.
Operating Instructions—Standard
To lower picture surface, pull screen down. Hesitate—then allow screen to
retract very slowly until it locks in place.
To raise picture surface, pull screen down and, while holding, allow for slow
retraction into the case to reduce risk of injury from falling screen.
Operating Instructions—AutoReturn
To lower picture surface, pull screen down. Hesitate—then allow screen to
retract very slowly until it locks in place.
To raise picture surface, pull screen down gently until it stops, then release.
Viewing Surface Care & Maintenance
Matt White & High Contrast Grey
Clean surface with a solution of mild dishwashing liquid diluted with warm
Mounting hardware supplied by others
7"
5
6
/
"
8
1
2
/
"
8
slot
E ngagement bracket (one on each end
of the bottom access panel) clicks into
place with the ball detent on each endcap.
1
5
/
"
2
1
/
"
3 2
8
3
/
"
8
1
3
/
"
8
Case Dimensions
9"
1"
11
/
"
16
11
/
"
16
6
5
/
"
8
3"
8"
2 3
4
/
"
3 2
Mounting Bracket Dimensions
1
1
/
"
1
/
"
2
2
R
1
/
"
4
1
/
"
8
1
/
"
4
5
/
"
16
R
1
/
"
8
www.draperinc.com
Retaining
clip
Standard Roller
B
A
water. Sponge the surface, rinse with clear water and blot dry. Do not use
clean ing solvents or abrasives.
Clean with a very soft brush or cloth and care ful ly dust the surface. DO
NOT USE SOAP, WATER, SOLVENTS OR ABRASIVES. These substances
will damage a glass beaded viewing surface.
Mounting brackets slide
left and right as needed.
3
/
"
16
1
4
/
"
2
1
1
/
"
4
13
4
/
"
16
7
3
/
"
4
9"
(765) 987-7999
Page 2 of 2
Roller
AutoReturn Roller
Roller
Hole
Dia. Position
1¾"
2¼"
3"
B
C
A
Glass Beaded
5
/
"
16
3
/
"
16
1
1
/
"
8
1
/
"
4
Roller pin
Retaining clip
Washer
Nylon bushing
Roller mtg. brkt.
A
B
C