AirStage ASHA18GBCH 운영 매뉴얼 - 페이지 4

{카테고리_이름} AirStage ASHA18GBCH에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AirStage ASHA18GBCH 8 페이지. Indoor unit (wall mounted type)

페이지 인쇄

CLEANING AND CARE

CAUTION

● Before cleaning the unit, be sure to stop the unit and disconnect the

power supply.

● Be sure the Intake Grille is installed securely.

● When removing and replacing the air filters, be sure not to touch the

heat exchanger, as personal injury may result.

● Do not clean the inside of the unit by yourself. To clean the inside,

always consult authorized service personnel.

● When cleaning the unit' body, do not use water hotter than 40 °C,

harsh abrasive cleansers, or volatile agents like benzene or thinner.

● Do not expose the unit body to liquid insecticides or hair sprays.

Cleaning the Intake Grille

1. Remove the Intake Grille.

(1) Place your fingers at both lower ends of the grille panel, and lift

forward; if the grille seems to catch partway through its movement,

continue lifting upward to remove.

(2) Pull past the intermediate catch and open the Intake Grille wide so

that it become horizontal..

Intake Grille

(2)

(1)

2. Clean with water.

Remove dust with a vacuum cleaner; wipe the unit with warm water, then

dry with a clean, soft cloth.

3. Replace the Intake Grille.

(1) Pull the knobs all the way.

(2) Hold the grille horizontal and set the left and right mounting shafts into

the bearings at the top of the panel.

(3) Press the place where the arrow on the diagram indicates and close

the Intake Grille.

Intake

Grille

Cleaning the Air Filter

1. Open the Intake Grille, and remove the air filter.

Lift up the air filter's handle, disconnect the two lower tabs, and pull out.

Air filter handle

Hooks

(two places)

En-3

Mounting

shaft

Knob

Mounting shaft

Bearing

(2)

Knob

(1)

Mounting shaft

Knob

2. Remove dust with a vacuum cleaner or by washing.

After washing, allow to dry thoroughly in a shaded place.

3. Replace the Air Filter and close the Intake Grille.

(1) Align the sides of the air filter with the panel, and push in fully, making

sure the two lower tabs are returned properly to their holes in the panel.

(2) Close the Intake Grille.

(For purposes of example, the illustration shows the unit without

Intake Grille installed.)

● Dust can be cleaned from the air filter either with a vacuum cleaner,

or by washing the filter in a solution of mild detergent and warm water.

If you wash the filter, be sure to allow it to dry thoroughly in a shady

place before reinstalling.

● If dirt is allowed to accumulate on the air filter, airflow will be reduced,

lowering operating efficiency and increasing noise.

● During periods of normal use, the Air Filters should be cleaned every

two weeks.

● When used for extended periods, the unit may accumulate dirt

inside, reducing its performance. We recommend that the unit be

inspected regularly, in addition to your own cleaning and care. For

more information, consult authorized service personnel.

● When shutting down the unit for one month or more, first allow the

fan mode to operate continuously for about one-half day to allow

internal parts to dry thoroughly.

Air Cleaning Filter Installation

1. Open the Intake Grille and remove the Air filters.

2. Install the Air cleaning filter set (set of 2).

(1) Set the air cleaning filter into the air cleaning filter frame.

Air cleaning filter set

Air cleaning filter

(2) Engage the latch at both ends of the filter with the two hooks at the rear

of the air cleaning filter frame.

Hook (2 places at the rear)

Take care that the air cleaning filter does not project beyond the frame.

(3) Engage the four fixing locations at the top and bottom of the air cleaning

filter frame with the hooks of the air filter.

Rear of the filter

Fixing location, hook (6 places)

Hooks

(two places)

Air Filter (Right & Left)

Air cleaning filter frame

Latch (2 places)