Bosch WAE 24163 사용 설명서 - 페이지 2

{카테고리_이름} Bosch WAE 24163에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch WAE 24163 8 페이지.

페이지 인쇄

1. Maintenance

Safety instructions

Care

– Read the instruction manual and installation instructions and all other information enclosed

with the washing machine and act accordingly.

– Retain the documents for subsequent use.

Risk of electric shock

– Never pull the cable to disconnect the mains plug.

– Never insert/disconnect the mains plug with damp hands.

Danger to life

For worn-out appliances:

– Disconnect the mains plug.

– Sever the mains cable and discard along with the plug.

– Destroy the lock on the washing machine door. This will prevent

children from locking themselves in and risking their lives.

Danger of suffocation

– Keep packaging, film and packaging parts out of the reach of

children.

Risk of poisoning

– Keep detergents and care products out of the reach of children.

– Items of laundry pretreated with cleaning agents containing

Risk of explosion

solvents, e.g. stain remover/cleaning solvent may cause an

explosion after being loaded into the washing machine.

1. Pull out, press insert down, remove draw completely.

Rinse items of laundry thoroughly by hand beforehand.

Risk of injury

– The washing machine door can become very hot.

– Be careful when draining hot detergent solution.

2. To remove the insert: press the insert upwards from below with your

– Do not climb onto the washing machine.

3. Clean the detergent dispenser tray and insert with water and a brush and

– Do not lean on the open washing machine door.

– Do not reach into the drum if it is still rotating.

4. Attach the insert and engage (connect the cylinder to the guide pin).

– Be careful when opening the detergent drawer while the machine

5. Push in the detergent drawer.

is in operation.

Consumption values

Programme

Load

Electricity***

Water***

duration***

Cottons 30 °C**

6 kg

0.51 kWh

55 l

2:22 h

Cottons 40 °C

6 kg

0.63 kWh

55 l

2:22 h

Cottons 60 °C

6 kg

1.26 kWh

55 l

2:31 h

2:35 h

Cottons 90 °C

6 kg

1.98 kWh

59 l

Easy-Care 40 °C**

3 kg

0.55 kWh

55 l

1:37 h

Information on the indicator lights

Mixed Load 40 °C**

3 kg

0.48 kWh

32 l

1:03 h

A signal sounds and indicator lights for the spin speed flash:

Delicate/silk 30 °C

2 kg

0.21 kWh

31 l

0:41 h

Close the washing

Wool 30 °C

2 kg

0.19 kWh

39 l

0:40 h

machine door properly;

laundry may be caught.

* Programme setting for testing in accordance with valid standard EN60456.

Note on comparative tests: For testing the test programmes, wash the specified load using the maximum spin speed.

Additional

Annual energy

Annual water

Programme

Load

function

consumption

Cottons 40/60 °C

Eco Perfect

6/3 kg

196 kWh

10120 l

Motor fault. Call the after-

** Programme setting for testing and energy labelling in accordance with EU directive 2010/30/EU with cold water (15 ºC).

sales service.

*** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient tem-

perature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional

functions.

– Risk of electric shock. Disconnect the

Maintenance

mains plug.

– Risk of explosion. No solvents.

Before washing for the first time

Detergent solution pump

Do not load any laundry into the machine. Turn on the tap. Add the following to compartment

Turn the programme selector to Off and disconnect the mains plug.

II:

– approx. 1 litre water

1. Open and remove the service flap.

– detergent (dosage according to the manufacturer's instructions for light soiling and the

appropriate degree of water hardness)

Set the programme selector to

Easy-Care 60 °C and select Start/Pause. At the end of the

2. For models with a drainage hose: Remove the drainage hose from the retainer and pull it

programme, turn the programme selector to Off.

from the housing. Remove the container.

Remove the sealing cap, allow the detergent solution to flow out.

Machine housing, control panel

Replace the sealing cap and place the drainage hose in the retainer.

– Wipe with a soft, damp cloth.

– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).

2* For models without a drainage hose: Carefully unscrew the pump cover until the

– Remove detergent and cleaning agent residue immediately.

detergent solution begins to flow out. When the service flap is half full, close the pump cover

and empty the service flap. Repeat the above steps until all the detergent solution has

– Do not clean with a jet of water.

completely drained out.

Cleaning the detergent drawer ...

3. Carefully unscrew the pump cover (residual water).

4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent

... if it contains detergent or fabric softener residues.

solution pump must rotate).

5. Replace the pump cover and screw it tightly in place.

6. Place the service flap back on and close.

finger.

dry it.

To prevent unused detergent from flowing straight into the drain during the next wash: pour 1 litre of water into

compartment II and start the

Drainage hose at the siphon

Leave the detergent drawer open so that any residual water can

Turn the programme selector to Off and disconnect the mains plug.

evaporate.

Drum

1. Loosen the hose clamp, carefully remove the drainage hose (residual water).

2. Clean the drainage hose and siphon connecting piece.

Leave the washing machine door open so that the drum can dry out.

3. Reattach the drainage hose and secure the connection with the hose clamp.

Rust stains - use chlorine-free cleaning agent, not steel wool.

Filter in the water supply

Descaling

Ensure there is no laundry in the machine

Risk of electric shock.

Descale the appliance according to the descaler manufacturer's instructions. This should not

Do not immerse the HydroSafe safety device in water (it contains an electric valve).

be necessary if the correct dosage of detergent is used.

Reduce the water pressure in the supply hose:

model-dependent

1. Turn off the tap.

2. Select any programme (except for

3. Select Start/Pause. Let the programme run for approximately 40 seconds.

Detergent solution pump

Open the tap completely,

4. Turn the programme selector to Off. Disconnect the mains plug.

blocked; Clean the

supply hose kinked or

Clean the filter:

detergent solution pump

trapped;

–> page 10.

Clean the filter

1. Depending on model:

Drainage hose/waste pipe

–> page 10,

Disconnect the hose from the tap.

blocked; Clean the drainage

Water pressure too low.

Clean the filter using a small brush.

hose at the siphon

–> page 10.

and/or for Standard and Aqua-Secure models:

Water in the base tub,

appliance leaking. Call the

Remove the hose on the rear of the appliance.

after-sales service.

Remove the filter with pliers and clean.

2. Connect the hose and check for leaks.

– Risk of scalding.

Allow the detergent solution to cool down.

What to do if ...

– Turn off the tap.

Water is leaking out.

– Attach/replace the drainage hose correctly.

– Tighten the screw connection of the supply hose.

No water supply.

– Start/Pause not selected?

– Tap not turned on?

Detergent not dispensed.

– Filter blocked? Clean the filter –> page 10.

– Supply hose kinked or trapped?

Washing machine door

– Safety function active. Wait approx. 2 minutes.

cannot be opened.

– Is Spülstop (Rinse Hold, without final spin) selected? –> page 3, 4.

Programme does not

– Start/Pause selected?

start.

– Washing machine door closed?

Detergent solution is not

– Is Spülstop (Rinse Hold, without final spin) selected? –> page 3, 4.

drained.

– Clean the detergent solution pump –> page 10.

– Clean the waste pipe and/or drainage hose.

Water not visible in the

– Not a fault - water below the visible area.

drum.

Unsatisfactory spin

– Not a fault - the unbalanced-load detection system has cancelled

result.

the spin cycle because of uneven distribution of the laundry.

Laundry wet/too damp.

Distribute small and large items of laundry evenly inside the

drum.

–

Reduced Ironing selected? –> page 5.

– Too low a speed selected? –> page 5.

Spin cycle performed

– Not a fault - unbalanced load detection system adjusts the

several times.

imbalance.

Residual water in the

– Not a fault - the action of the care product is not affected.

Drain programme.

compartment for care

– Clean the insert if necessary –> page 9.

products.

Odour formation in the

– Run programme

standard detergent.

washing machine.

Foam escaping from the

– Too much detergent used?

detergent drawer.

If foam is escaping from the detergent drawer:

Mix 1 tablespoon of fabric softener with ½ litre of water and pour

into compartment II (not with outdoor or down fabrics).

– Reduce the detergent dosage for the next wash cycle.

Intense noise formation,

– Are the appliance feet fixed?

vibrations and "walking"

Secure the appliance feet –> Installation instructions.

during the spin cycle.

– Transportation safety devices removed?

Remove the transportation safety devices –> Installation

instructions.

The indicator lights do

– Power cut?

Rinse / Spin

Drain).

not function during

– Fuses tripped? Reset/change the fuse.

operation.

– If the fault occurs repeatedly, call the after-sales service.

Programme sequence

– Not a fault - unbalanced load detection system adjusts

longer than usual.

imbalance by repeatedly distributing the laundry.

– Not a fault - foam detection system active - adds an additional

rinse cycle.

Detergent residues on

– Occasionally, phosphate-free detergents contain water-insoluble

the laundry.

residues.

– Select

Rinse/Spin

If you cannot correct a fault yourself or a repair is required:

– Turn the programme selector to Off and remove the mains plug from the socket.

– Turn off the water supply and call the after-sales service –> Installation instructions.

Cottons 90 °C without laundry. Use

Washing machine

en Instruction manual

or brush out the laundry after washing.