Draper Silhouette M Series 설치 및 운영 지침

{카테고리_이름} Draper Silhouette M Series에 대한 설치 및 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper Silhouette M Series 2 페이지. Manually operated projection screens
Draper Silhouette M Series에 대해서도 마찬가지입니다: 서비스 교체 부품이 포함된 설치/운영 매뉴얼 (5 페이지)

페이지 인쇄

Manually Operated Projection Screens by Draper

➀

Read instructions through completely before proceeding; keep

them for future reference. Follow instructions carefully. Installation

contrary to instructions invalidates warranty. Care in both mounting

and correct operation willl assure long and satisfactory service from

your Draper screen.

➁

Screen should be accessible for complete removal should fabric

become damaged or for service if required.

➂

Screen should be installed level (using a carpenter's level).

➃

Nothing should be fastened to screen dowel or viewing surface.

➄

Operating crank for Series C is packed separately in screen carton.

Do not discard with packing material.

Note: Screen has been thoroughly inspected and tested at factory

and found to be operating properly prior to shipment.

Installation

Your Draper screen can be mounted on a wall or suspended from the ceiling,

or mounted on special 6" extension bracket. Extension brackets must be

ordered separately from Draper . With each method of installation, the case

must be mounted level and with the flat back parallel to the wall.

To reduce the risk of personal injury, use only the hardware which comes

with the screen or is specified in these instructions.

The screen (or extension brackets) should be mounted into studs or

blocking in the wall/ceiling, or in drywall (minimum thickness

specified anchors. For any other type of installation, follow all local building

and safety codes.

Steel studs, concrete or cinder block walls and all other types of non-wood

frame construction require the use of special screws or anchors. The

selection of appropriate mounting hardware should be made by a qualified

professional installer.

When locating viewing surface and checking clearance for screen's opera-

tion, remember surface is centered in case. Handle case carefully to avoid

scratching. Regardless of mounting method, screen should be positively

and securely supported so that vibration or even abusive pulling on the

viewing surface will not cause case to work loose or fall. Installer must insure

that fasteners used are of adequate strength and suitable for the mounting

surface.

Wall Mounting

Mount 2, 3, or 4 aluminum brackets provided ("Z" Clips) on the wall at desired

height, using appropriate fasteners. Verify that they are in line and level to

fully engage with the mounting lip on back of screen case. 1

is required above the "Z" Clips to allow case lip to be engaged over the lip

of the "Z" Clips.

Engage the lip on back of screen case with lip of "Z" Clip and gently pull down

to fully engage case to brackets.

411 S. Pearl St., Spiceland, IN 47385 USA ❚ 765-987-7999 ❚ fax 765-987-7142

e-mail [email protected] ❚ www.draperinc.com

Installation/Operating Instructions

Silhouette/Series M and C

Caution

" of free space

Form Sil/MCI00

Lip on back

of case

"Z" Clip

(wall mounting bracket

supplied with Silhouette)

Locate 2 offset ceiling brackets (supplied) and slide these into the channel

on top of screen case by angling one side of bracket under lip of channel and

opposite side of bracket above notch in opposite channel lip.

Allow bracket to drop against bottom of channel and then slide it along case

") with

until it stops against endcap of case. Tighten 2 set screws to lock bracket

in place. Make sure that the flange of the ceiling bracket that has 4 holes is

extended beyond the endcaps of the case. Repeat above procedure for

second ceiling bracket, making sure to slide it towards opposite end of case.

To mount against ceiling, hold screen case against ceiling and mark

mounting hole locations. Each bracket has 2 holes towards the front edge

and 2 holes towards the back edge. Installer must use at least 2 fasteners

(front of Silhouette case)

per bracket with one fastener in one of the two holes closest to back edge

of bracket, and one fastener in one of the two holes closest to front edge of

bracket. Installer must insure that fasteners are of adequate strength and

suitable for the mounting surface chosen.

To mount suspended from ceiling, the brackets need to be installed on

screen case as noted above. Attach "S" Hooks (supplied) through the holes

in the brackets. Select the set of holes that allows the screen to hang in a

vertical position. The installer is to provide the materials and fasteners to

attach the "S" Hooks to the ceiling. Installer must insure that the fasteners

and suspension material are of adequate strength and suitable for the

mounting surface chosen.

Printed in U.S.A.

Silhouette fully engaged

on "Z" Clip

Ceiling/Suspended Mounting

Ceiling bracket in

channel of case

Ceiling bracket

Mounting fasteners

(supplied by others, 2 per bracket)

(right end of Silhouette case)