Draper SLX14 설치 및 운영 지침 매뉴얼

{카테고리_이름} Draper SLX14에 대한 설치 및 운영 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper SLX14 7 페이지. 230v ac scissor lift slx video projector lift
Draper SLX14에 대해서도 마찬가지입니다: 브로셔 및 사양 (16 페이지), 설치 및 운영 매뉴얼 (7 페이지), 설치 및 작동 지침 (8 페이지), 설치 및 운영 지침 (4 페이지), 설치 및 운영 지침 매뉴얼 (7 페이지)

페이지 인쇄

Scissor Lift SLX Video Projector Lift by Draper

1 Read instructions completely before proceeding.

2 Test lift prior to installation. Please Note: Packaging must be removed from lift

before testing.

3 Follow instructions carefully. Installation contrary to instructions invalidates warranty.

4 Do not obstruct operation of Scissor Lift SLX with fingers or any object. Serious

injury or damage could result.

5 Maximum lifting capacity is 350 Lbs.

6 Scissor Lift SLX is designed to accommodate ceiling suspended equipment.

Equipment should not be allowed to rest on optional ceiling closure during

operation (refer to section titled "Installing Projector").

7 Entire bottom of unit must be unobstructed to permit proper operation. Sufficient clear-

ance must be allowed below projector or optional ceiling closure: 10' for Model SLX10,

14' for Model SLX14, etc.

8 Unit must be installed level (use a carpenter's level).

9 Unit operates on 110-120V AC 60 Hz. current.

10 Verify the show position when testing lift. Make required changes by referring to

adjustment instructions on page 4 of this document.

11 The maintenance/service factory limit setting must not be adjusted to a lower

position than the preset factory limit setting. In addition, Draper does not

recommend setting show position at the maintenance/service position—for

example, if you wish to have 8' Show position, order a lift with at least a 10'

maintenance position.

CAUTION: Before servicing unit, disconnect hardwired control and any

remote control.

Note: Unit has been thoroughly inspected and tested at factory and found to be

operating properly prior to shipment.

1 Based on screen location and projector specifications, determine proper

position for projector installation.

2 Confirm that there is adequate space for installation and operation. Minimum

clearance above ceiling level varies according to Scissor Lift model, plus height

of projector, optional mounting bracket, optional ceiling closure, and optional

Environmental Air Space Housing.

3 Arrange to provide service access to the unit.

4 Maximum lifting capacity is 350 Lbs.

As Soon As Scissor Lift Arrives

1 Open carton and inspect for damage.

2 Locate the following parts:

A. The unit itself

B. Controls

C. Optional equipment: Environmental Air Space Housing, Universal

Projector Mount, closure panel or ceiling finish kit (all ship in separate

cartons).

3 Test lift prior to installation. Please Note: Packaging must be removed from

lift before testing.

Hanging Unit

Please note: If using Environmental Air Space Housing option, go to

Environmental Air Space Housing instructions on page 7.

The Scissor Lift may be installed in a variety of ways; recessed above the

ceiling, or suspended below the ceiling. The lift should be supported by four ½"

threaded mounting rods. If ceiling recessed, the entire unit (including the projector)

should set approximately 1½" above the finished ceiling in its "stored" position. The

threaded rods should pass through the corner mounting flanges and be secured

by nuts above and below. The unit should then be guy wired or blocked to prevent

swinging.

All installations should observe the following guidelines:

1 If installing above a hard ceiling, optional Draper Access Panels are available to

allow access to the unit.

2 Installer must ensure that all fasteners and supports are of adequate strength to

securely support Scissor Lift and projector.

3 Fastening methods must be suitable for mounting surface, and securely

anchored so that vibration or abusive pulling on unit will not weaken installation.

4 Unit should be level, with weight shared more or less equally by all four

threaded mounting rods.

5 Bottom of unit must be unobstructed after installation. Sufficient clearance must

be allowed below projector or optional ceiling closure.

6 Do not use unit to support adjacent ceiling, light fixtures, etc.

7 Do not complete the ceiling below unit until electrical connections have been

completed and unit has been operated successfully.

8 We recommend that safety cables be attached to the Scissor Lift SLX for

Installation/Operating Instructions

Caution:

Planning

Caution: Beware

of pinch points

added security (a sound installation practice with overhead equipment).

9 When the Scissor Lift SLX is to be installed in "other space used for

environmental air" the optional environmental air space housing must

be installed per instructions to isolate the lift from the "other space

used for environmental air."

Electrical Connections

Unit operates on 110-120V AC, 60 Hz. current.

Opening the electrical box exposes terminals for field connections. Unit is shipped

with internal wiring complete.Wire to connect unit to power supply should be

furnished by installer. Connections should be made in accordance with wiring

diagram, and wiring should comply with national and local electrical codes. All

operating switches should be "off" before power is connected.

Caution: Make sure electrical supply has been disconnected before

attempting to connect Scissor Lift to electricity.

Scissor Lift should be operated and checked prior to installing projector and/or

optional ceiling closure.

Low Voltage Control Switch shown below comes with 75' of cable and should be

plugged in to Control Panel on top frame of lift for control of the "Up" and "Show"

positions. Momentary Key Switch shown below comes with 75' of cable and should

be plugged in to Control Panel on top frame of lift for control of the "Service"

position.

LVC-S

Up & Show

2¾"

4½"

Front

Before operating or testing the unit, make sure the packaging has been

removed from the unit. This can be accomplished by removing the eight screws

(four per side) holding the packing frame to the lift. Once the packaging is all

removed, operate the lift in the "Up" direction, so the lift's control encoder will

recognize it's "home" location. Until you do this, the Down function will not work.

When unit is first operated, be cautious! If unit fails to operate properly, press

"off" and recheck electrical connections before proceeding. Cycle unit down and

up several times to confirm satisfactory operation. You must also do this if the

Scissor Lift ever loses or is disconnected from the power.

Caution: Do not pull on or touch safety belt when unit is in motion. If belt

locks, the cables will unspool.

Caution: Obstructing bottom pan may cause cables to unspool.

Standard Single Station Low Voltage Control (See Fig. 1)—One three-button

switch with "Up", "Down", and "Off" buttons. Lift starts up or down when appropriate

button is pressed, and may be stopped by pressing "Off" button. Factory set

limit switches stop lift automatically when projector is in "show" position. One

momentary key switch lowers lift from "Show" to "Service" position.

Optional Multiple Station Control—Optional, moves lift from "Stored" to "Show"

position only. Each switching station has a three-button switch with "Up", "Down",

and "Off" buttons. Lift starts up or down when appropriate button is pressed,

and may be stopped by pressing "Off" button. Factory set limit switches stop lift

automatically when projector is in "Show" position.

Optional Key Operated Switch—If ordered, the standard LVC-S can be replaced

with a second single station, momentary key-operated three position (up/off/down)

switch. Multiple Station Control required for this option. Moves lift from "stored" to

"show" position only.

Optional Infrared or Radio Frequency Remote Control—If ordered, a three-

button transmitter is provided, with "up", "down", and "stop" buttons. Unit starts up

or down when appropriate button is pressed, and may be stopped by pressing

"off" button. Factory set limit switches stop unit automatically when projector is in

"show" position. Only controls "show" and "stored" positions.

Optional RS232 Control—For Serial communication an R2D7 Serial

Communications Interface is optionally available.

Low Voltage Trigger—Input provided for Low Voltage Trigger from projector (see

diagram on page 4).

Please Note: Scissor Lift SLX must be installed in accordance with the

requirements of the Local Building Codes, the Canadian Electrical Code

(CEC), CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70, as

required. An appropriate disconnect device shall be provided as part of the

building installation.

If you encounter any difficulties installing or servicing your Scissor Lift SLX, call your

dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999, or fax 765-987-7142.

SP-KSM

Service

OFF

DOWN

D C U

Side

Back

Figure 1

Operation