Draper V Series 설치 및 운영 지침

{카테고리_이름} Draper V Series에 대한 설치 및 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper V Series 4 페이지. 220v ultimate access
Draper V Series에 대해서도 마찬가지입니다: 설치 및 운영 지침 (4 페이지)

페이지 인쇄

Silhouette/Series E & V Electric Projection Screen by Draper

➀ Read instructions through completely before proceeding; keep them for

future reference. Follow instructions carefully. Installation con trary to

instructions in val i dates warranty. Care in mounting and correct oper-

ation will mean long and satisfactory service from your Draper screen.

➁ Screen should be accessible for complete removal should fabric

become damaged or should other service be required.

➂ Screen should be installed level (using a carpenter's level).

➃ Nothing should be fastened to screen dowel or viewing surface

➄ Operating switch(es) packed separately in screen carton. Do not

discard with packing material.

➅ Screen operates on 110-120v, 60 hz. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only. They do not

imply any re spon si bil i ty on the part of Draper, Inc. for improper

in stal la tion or faulty work man ship at the jobsite.

Installation

Your Draper screen can be mounted on a wall or suspended from the ceiling,

or mounted on special 6" or 12" extension brackets. Extension brackets must

be ordered separately from Draper. With each method of in stal la tion, the case

must be mounted level and with the ﬂ at back parallel to the wall.

To reduce the risk of personal injury, use only the hardware which comes with

the screen or is speciﬁ ed in these instructions.

The screen (or extension brackets) should be mounted into studs or block-

ing in the wall/ceiling, or in drywall (minimum thickness

anchors. For any other type of installation, follow all local build ing and safety

codes.

Steel studs, concrete or cinder block walls and all other types of non-wood

frame construction require the use of special screws or anchors. The selection

of ap pro pri ate mounting hardware should be made by a qualiﬁ ed pro fes sion al

installer.

When locating viewing surface and checking clearance for screen's operation,

remember surface is centered in case.

Take care to install wall/ceiling electrical box and conduit so they will be fully

concealed by the screen case after installation.

Handle case carefully to avoid scratching.

Regardless of mounting method, screen should be positively and securely

supported so that vibration or even abusive pulling on the viewing surface will

not cause case to work loose or fall. Installer must insure that fasteners used

are of adequate strength and suitable for the mounting surface chosen.

Wall Mounting

Mount 2, 3, or 4 aluminum brackets provided ("Z" Clips) on the wall at desired

height, using appropriate fasteners. Verify that they are in line and level to fully

engage with the mounting lip on back of screen case. 1

required above the "Z" Clips to allow case lip to be engaged over the lip of the

"Z" Clips.

Engage the lip on back of screen case with lip of "Z" Clip and gently pull down

to fully engage case to brackets.

Installation/Operating Instructions

Caution

") with speciﬁ ed

" of free space is

Form SilhouetteE&V_Inst04

Lip on back of case

Lo cate 2 off set ceil ing brack ets (supplied) and slide these into the channel

on top of screen case by angling one side of bracket under lip of channel and

opposite side of bracket above notch in opposite channel lip.

Allow bracket to drop against bottom of channel and then slide it along case

until it stops against end cap of case. Tighten 2 set screws to lock bracket in

place. Make sure that the ﬂ ange of the ceiling bracket that has 4 holes is ex-

tended beyond the end caps of the case. Repeat above procedure for second

ceiling brack et, making sure to slide it towards op po site end of case.

To mount against ceiling, hold screen case against ceiling and mark

mounting hole locations. Each brack et has 2 holes towards the front edge

and 2 holes towards the back edge. Installer must use at least 2 fasteners

per bracket with one fastener in one of the two holes clos est to back edge

of bracket, and one fas ten er in one of the two hole closest to front edge of

bracket. Installer must insure that fasteners are of adequate strength and suit-

able for the mounting surface chosen.

(front of Silhouette case)

Printed in U.S.A.

Silhouette fully engaged

on "Z" Clip

"Z" Clip

(wall mounting bracket

supplied with Silhouette)

Ceiling/Suspended Mounting

Ceiling bracket in

channel of case

Ceiling bracket

Mounting fasteners

(supplied by others, 2 per bracket)

(right end of Silhouette case)