Bosch WAE28366GB Series 사용 설명서 - 페이지 2

{카테고리_이름} Bosch WAE28366GB Series에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch WAE28366GB Series 8 페이지.

페이지 인쇄

Safety instructions

Care

– Read the instruction manual and installation instructions and all other information enclosed

with the washing machine and act accordingly.

– Retain the documents for subsequent use.

Risk of electric shock

– Never pull the cable to disconnect the mains plug.

– Never insert/disconnect the mains plug with damp hands.

Danger to life

For worn-out appliances:

– Disconnect the mains plug.

– Sever the mains cable and discard along with the plug.

– Destroy the lock on the washing machine door. This will prevent

children from locking themselves in and risking their lives.

Danger of suffocation

– Keep packaging, film and packaging parts out of the reach of

children.

Risk of poisoning

– Keep detergents and care products out of the reach of children.

Risk of explosion

– Items of laundry pretreated with cleaning agents containing

solvents, e.g. stain remover / cleaning solvent may lead to an

1. Pull out, press insert down, remove draw completely.

explosion after being loaded into the washing machine.

2. To remove the insert: press the insert upwards from below with your finger.

Rinse items of laundry thoroughly by hand beforehand.

3. Clean the detergent dispenser tray and insert with water and a brush and dry it.

4. Attach the insert and engage (connect the cylinder to the guide pin).

Risk of injury

– The washing machine door can become very hot.

5. Push in the detergent drawer.

– Be careful when draining hot detergent solution.

– Do not climb onto the washing machine.

– Do not lean on the open washing machine door.

– Do not reach into the drum if it is still rotating.

– Be careful when opening the detergent drawer while the machine

is in operation.

Consumption values

Additional

Electricity con-

Programme

Load

Water***

function

sumption***

duration***

Cottons 30 °C**

6 kg

0,51 kWh

55 l

2:21 h

Cottons 40 °C**

6 kg

0,63 kWh

55 l

2:21 h

Cottons 60 °C**

6 kg

1,26 kWh

55 l

2:29 h

Cottons 60 °C

EcoPerfect*

6 kg

1,02 kWh

45 l

2:49 h

Cottons 90 °C

6 kg

1,98 kWh

59 l

2:34 h

Easy-Care 40 °C**

3 kg

0,55 kWh

55 l

1:37 h

3 kg

0,48 kWh

32 l

1:03 h

1. Turn the programme selector to Off and disconnect the mains plug.

Mixed Load 40 °C**

2. Drain the detergent solution –> page 10.

Delicate/Silk 30 °C

2 kg

0,21 kWh

31 l

0:41 h

3. Pull the emergency release downwards with a tool and release.

Wool cold

2 kg

0,10 kWh

39 l

0:40 h

Wool 30 °C

2 kg

0,19 kWh

39 l

0:40 h

Information on the display panel

* Programme setting for testing and energy labelling in accordance with EU directive 92/75/EEC.

** Programme setting for testing in accordance with valid standard EN60456.

F: 16

Note on comparative tests: Try out the test programme by washing the specified load using the maximum spin speed.

F: 17

As a short programme for coloureds, select the programme

Mixed Load 40 °C with the maximum spin speed.

*** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient tem-

perature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional

F: 18

functions.

F: 21

F: 23

– Risk of electric shock. Disconnect the mains plug.

Maintenance

– Risk of explosion. No solvents.

Before washing for the first time

Detergent solution pump

Do not load any laundry into the machine. Turn on the tap. Add the following to compartment II:

Turn the programme selector to Off and disconnect the mains plug.

– approx. 1 litre water

1. Open and remove the service flap.

– detergent (dosage according to the manufacturer's instructions for light soiling and the appropriate degree of water

hardness)

Set the programme selector to

Easy-Care 60 °C and select

Start/Reload. At the end of the programme, turn

the programme selector to Off.

2. For models with a drainage hose: Remove the drainage hose from the retainer and pull it

Machine housing, control panel

from the housing. Remove the container.

Remove the sealing cap, allow the detergent solution to flow out.

– Wipe with a soft, damp cloth.

Replace the sealing cap and place the drainage hose in the retainer.

– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).

– Remove detergent and cleaning agent residue immediately.

2* For models without a drainage hose: Carefully unscrew the pump cover until the

– Do not clean with a jet of water.

detergent solution begins to flow out. When the service flap is half full, close the pump cover

and empty the service flap. Repeat the above steps until all the detergent solution has

Cleaning the detergent drawer ...

completely drained out.

... if it contains detergent or fabric softener residues.

3. Carefully unscrew the pump cover (residual water).

4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent

solution pump must rotate).

5. Replace the pump cover and screw it tightly.

6. Place the service flap back on and close.

Leave the detergent drawer open so that any residual water can evaporate.

To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into

compartment II and start the

Drum

Drainage hose at the siphon

Leave the washing machine door open so that the drum can dry out.

Turn the programme selector to Off and disconnect the mains plug.

Rust stains - use chlorine-free cleaning agent, not steel wool.

Descaling

Ensure there is no laundry in the machine

1. Loosen the hose clamp, carefully remove the drainage hose (residual water).

2. Clean the drainage hose and siphon connecting piece.

Descale the appliance according to the descaler manufacturer's instructions. This should not be necessary if the

correct dosage of detergent is used.

3. Reattach the drainage hose and secure the connection with the hose clamp.

Emergency release, e.g. in the event of a power cut

Filter in the water supply

Risk of electric shock!

The programme continues to run when the power has been restored. However, if the laundry has to be removed, the

Do not immerse the HydroSafe safety device in water (contains an electric valve).

washing machine door can be opened as follows:

Risk of scalding.

Reduce the water pressure in the supply hose:

The detergent solution and laundry may be hot. If possible, leave it to cool down.

Do not reach into the drum if it is still rotating.

1. Turn off the tap.

Do not open the washing machine door if water can be seen through the glass.

2. Select any programme (except for Rinse/Spin /

3. Choose

Start/Reload. Let the programme run for approximately 40 seconds.

4. Turn the programme selector to Off. Disconnect the mains plug.

Clean the filter:

Washing machine door can then be opened.

1. Depending on model:

Disconnect the hose from the tap.

Clean the filter using a small brush.

depending on model

Close the washing machine door properly; laundry may be caught.

and/or for Standard and Aqua-Secure models:

Open the tap completely, supply hose kinked or trapped;

Remove the hose on the rear of the appliance,

Clean the filter –> page 10, Water pressure too low.

Remove the filter with pliers and clean.

Detergent solution pump blocked; Clean the detergent solution pump –> page 10. Drainage hose / waste pipe

2. Connect the hose and check for leaks.

blocked; Clean the drainage hose at the siphon –> page 10.

Motor fault. Call customer services.

Water in the base tub, appliance leaking. Call customer services.

– Risk of scalding.

Allow the detergent solution to cool down.

What to do if ...

– Turn off the tap.

Water is leaking out.

– Attach/replace the drainage hose correctly.

– Tighten the screw connection of the supply hose.

No water supply.

–

Start/Reload not selected?

Detergent not

– Tap not turned on?

dispensed.

– Filter blocked? Clean the filter –> page 10.

– Supply hose kinked or trapped?

Washing machine door

– Safety function active. Programme stopped? –> page 4.

cannot be opened.

– Is Rinse Hold (without final spin) selected? –> page 3, 4.

– Can be opened by emergency release only? –> page 9.

Programme does not

–

Start/Reload or

start.

– Washing machine door closed?

– Childproof lock active? Deactivate –> page 5.

Detergent solution is

– Is Rinse Hold (without final spin) selected? –> page 3, 4.

not drained.

– Clean the detergent solution pump –> page 10.

– Clean the waste pipe and/or drainage hose.

Water not visible in the

– Not a fault - water below the visible area.

drum.

Unsatisfactory spin

– Not a fault - the unbalanced-load detection system has cancelled

result.

the spin cycle because of uneven distribution of the laundry.

Laundry wet/too damp.

Distribute small and large items of laundry evenly inside the drum.

–

Reduced Ironing selected? –> page 5.

– Selected speed too low? –> page 5.

The programme length

– Not a fault - the number of spin cycles may be changed due to the

jumps during the final

varying distribution of the laundry, which may cause the time in the

spin.

display panel to be corrected.

Drain programme.

Spin cycle performed

– Not a fault - unbalanced load detection system adjusts the

several times.

imbalance.

Residual water in the

– Not a fault - the action of the care product is not affected.

compartment for care

– Clean the insert if necessary –> page 9.

products.

Odour formation in the

– Run programme

washing machine.

detergent.

Foam escaping from

– Too much detergent used?

the detergent drawer.

If foam is escaping from the detergent drawer:

Mix 1 tablespoon of fabric softener with ½ litre of water and pour

into compartment II (not with outdoor or down fabrics).

– Reduce the detergent dosage for the next wash cycle.

Intense noise

– Are the appliance feet fixed?

formation, vibrations

Secure the appliance feet –> Installation instructions.

and "wandering"

– Transportation safety devices removed?

Drain).

during the spin cycle.

Remove the transportation safety devices –> Installation

instructions.

Display panel/indicator

– Power cut?

lamps do not function

– Fuses triggered? Reset/change the fuse.

during operation.

– If the fault occurs repeatedly, call customer services.

Programme sequence

– Not a fault - unbalanced load detection system adjusts imbalance

longer than usual.

by repeatedly distributing the laundry.

– Not a fault - foam detection system active - adds an additional rinse

cycle.

Detergent residues

– Occasionally, phosphate-free detergents contain water-insoluble

on the laundry.

residues.

– Select the Rinse/Spin cycle or brush out the laundry after washing.

If you cannot correct a fault yourself (switching on/off) or a repair is required:

– Turn the programme selector to Off and remove the mains plug from the socket.

– Turn off the water supply and call customer services –> Installation instructions.

Ready in time selected?

Washing machine

Cottons 90 °C without laundry. Use standard

Instruction manual

Observe the safety instructions on page 8.

Read these instructions and the separate installation instructions before

operating the washing machine.