Draper CSM185C 사용 설명서 - 페이지 5
{카테고리_이름} Draper CSM185C에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper CSM185C 12 페이지. Metal cutting saw 185 mm
페이지 인쇄
WARNING:
Please read the following instructions carefully, failure to do so could lead to serious personal injury. When using electric tools, basic
safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury.
Read all these instructions before operating this product and save these instructions.
IMPORTANT:
Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it
was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you.
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels
affixed to the tool. Learn its application and limitations
as well as the specific potential hazards peculiar to
this tool.
2. KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents.
Floors must not be slippery due to oil or sawdust.
3. AVOID DANGEROUS ENVIRONMENTS
Do not use power tools in damp or wet locations, or
expose them to rain. Keep work area well lit. Provide
adequate space surrounding the work area. Do not use
in environments with a potentially explosive atmosphere.
4. KEEP CHILDREN AWAY
All visitors should be kept a safe distance from work area.
5. STORED TOOLS
When not being used, all tools should be stored in a
dry, locked cupboard and out of the reach of children.
6. WEAR PROPER CLOTHING
Do not wear loose clothing, neckties or jewellery (rings,
wristwatches) to catch in moving parts. NONSLIP
footwear is recommended. Wear protective hair covering
to contain long hair. Roll long sleeves above the elbow.
7. USE SAFETY GOGGLES (Head Protection)
Wear CE approved safety goggles at all times. Normal
spectacles only have impact resistant lenses, they are
NOT safety glasses. Also, use face or dust mask if
application is dusty and ear protectors (plugs or muffs)
during extended periods of operation.
8. NOISE LEVELS
Some types of machines may have high noise levels
when working. In such cases ear protection must be worn.
9. VIBRATION LEVELS
Hand held power tools produce different vibration
levels. You should always refer to the specifications and
relevant Health and Safety guide.
10. DUST EXTRACTION
If your tool is fitted with a dust extraction fitting, always
ensure that it is connected and being used with a dust
extractor. Vacuum cleaners can be used if suitable for
the material being extracted.
11. PROTECT YOURSELF FROM ELECTRIC SHOCK
When working with power tools, avoid contact with any
earthed items (e.g. pipes, radiators, hobs and
refrigerators, etc.). If you are using a power tool in
extreme conditions (e.g. high humidity or generating
metal dust), always use an RCD (residual current
device) at the power socket.
12. STAY ALERT
Always watch what you are doing and use common
sense. Do not operate a power tool when you are tired
or under the influence of alcohol or drugs.
13. WHEN WORKING OUT OF DOORS
Only use extension leads designed for that purpose.
14. ACCESS TO MAINS SOCKET
If a stationary machine is fitted with a moulded plug and
cable, the machine should not be positioned so that
access to the mains socket is restricted.
15. DISCONNECT POWER TO THE TOOL
When not in use, before servicing and when changing
accessories such as cutters, etc.
16. AVOID ACCIDENTAL STARTING
Make sure the switch is in the OFF position before
plugging the machine into the power supply.
IMPORTANT NOTE:
Residual Risk. Although the safety instructions and operating manuals for our tools contain extensive instructions on safe working
with power tools, every power tool involves a certain residual risk which can not be completely excluded by safety mechanisms.
Power tools must therefore always be operated with caution!
GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS
17. NEVER LEAVE MACHINE RUNNING UNATTENDED
Turn power off. Do not leave machine until it comes to a
complete stop.
18. DO NOT ABUSE THE CORD
Never carry the tool by the power cable or pull it from
the socket. Keep the power cable away from heat, oil
and sharp edges. If the supply cord is damaged, it must
be replaced by the manufacturer or its service agent or
a similarly qualified person in order to avoid hazard.
19. NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped or if the
cutting tool is accidentally contacted. Do not store
materials above or near the tool, so that it is necessary
to stand on the tool to reach them.
20. CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part that
is damaged should be carefully checked to determine
that it will operate properly and perform its intended
function. Check for alignment of moving parts, free
running of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation.
A guard or other part that is damaged should be
repaired properly or replaced by an authorized service
centre unless otherwise indicated in this instruction
manual. Have defective switches replaced by an
authorized service facility. Do not use the tool if the
switch does not turn it on and off.
21. KEEP GUARDS IN PLACE
And in working order.
22. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for the best and safest
performance. Follow instructions for lubricating and
changing accessories. All extension cables must be
checked at regular intervals and replaced if damaged.
Always keep the hand grips on the tool clean, dry and
free of oil and grease.
23. USE RECOMMENDED ACCESSORIES
Consult the owners manual for recommended
accessories. Follow the instructions that accompany
the accessories. The use of improper accessories may
cause hazards .
24. REMOVE ADJUSTING KEYS AND WRENCHES
Form a habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning it on.
25. SECURE WORK
Use clamps or a vice to hold work. This frees both hands
to operate the tool.
26. DO NOT OVERREACH
Keep proper footing and balance at all times.
27. USE RIGHT TOOL
Do not force the tool or attachment to do a job for which
it was not designed.
28. DO NOT FORCE TOOL
It will do the job better and safer at the rate for which it
was designed.
29. DIRECTION OF FEED
Feed work into a blade or cutter against the direction
of rotation of the blade or cutter only.
30. WHEN DRILLING OR SCREWING INTO WALLS
Always make sure there is no danger of hitting any
hidden power cables, water or gas pipes in the wall.
31. HAVE YOUR TOOL REPAIRED BY A QUALIFIED PERSON
This electric tool is in accordance with the relevant safety
requirements. Repairs should only be carried out by
qualified persons using original spare parts, otherwise
this may result in considerable danger to the user.
- 4 -