Draper Clutch Operated FlexShade 설치 및 작동 지침 - 페이지 3
{카테고리_이름} Draper Clutch Operated FlexShade에 대한 설치 및 작동 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper Clutch Operated FlexShade 7 페이지.
페이지 인쇄Clutch Operated FlexShade
Window shade with smooth, quiet operation, and independent control
Section 1 - Bead Chain Clutch Installation
Caution: Before mounting shades, verify measurements on card provided with shade, and ensure brackets are installed at correct width.
Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions.
Section 1.1 - 20# Clutches
1. Mark wall, jamb or ceiling for placement of mounting brackets. and drill small starter hole
2. Place spring-loaded pin into idler bracket, slip notches on clutch into clutch bracket. Press down to lock in place.
Small Universal Brackets - 20# Clutch Installation
1
/
"
9
16
(40mm)
1
9
/
"
16
(40mm)
2
3
/
"
8
(60mm)
2
/
"
3
8
(60mm)
15
/
"
16
(24mm)
2 ¼"
/
"
15
16
(31mm)
(24mm)
2 ¼"
(31mm)
/
"
15
16
(24mm)
15
/
"
16
(24mm)
Large Universal Brackets - 20# Clutch Installation
2 ¼"
2 ¼"
(54mm)
(54mm)
2
/
"
7
2
7
/
8
"
(73mm)
8
(73mm)
/
"
15
15
/
16
"
(24mm)
16
(24mm)
/
"
15
15
/
16
"
(24mm)
16
(24mm)
Section 1.2 - 24# Clutches
1. Mark wall, jamb or ceiling for placement of mounting brackets and drill small starter hole
2. Install clutch end onto spear on operator bracket, slide notched pin into idler racket, then place retainer clip.
24# Idler & Clutch Brackets - 24# Clutch Installation
2 ¼"
2 ¼"
(57mm)
3 ¼"
(83mm)
2
3
/
"
8
(60mm)
Idler
Caution: Be sure retainer clip installed on roller with 24 lb clutch.
DO NOT use 24 lb. clutch wall brackets on ceiling installations, and DO NOT use 24 lb. clutch ceiling brackets for wall installations.
24 lb. Clutches are LEFT and RIGHT specific.
(Brackets Only)
(see Fig. 2 and Fig. 3)
Small
2
/
" x 2
/
"
Bracket
3
3
8
16
(60 x 56mm)
11
/
"
16
(17mm)
/
"
11
16
(17mm)
2
3
/
"
16
(56mm)
2
/
"
3
16
(56mm)
2 ¾"
(44mm)
2 ¾"
(44mm)
Large
/
/
2
" x 2
"
7
3
8
16
(73 x 56mm)
11
/
"
/
"
11
16
(17mm)
16
(17mm)
2
3
/
"
2
/
"
3
16
(56mm)
16
(56mm)
2 ¾"
2 ¾"
1
/
"
7
(44mm)
1
7
/
8
"
(44mm)
(30mm)
8
(30mm)
(see Fig. 4)
3 ¼"
(83mm)
2 ¾"
(67mm)
2 ¼"
Clutch
(57mm)
®
(if necessary)
Idler
Idler End
of Roller
Retainer Clip
Idler
Idler End
Bracket
of Roller
Retainer Clip
(if necessary)
Idler
Idler End
Bracket
2 ¼"
2 ¼"
(57mm)
of Roller
Retainer Clip
in mounting surface.
10 lb Clutch
10 lb Clutch
in mounting surface.
24 lb Clutch
3 ¼"
(83mm)
2
3
/
"
8
(60mm)
45°
page 3 of 7
Figure 2
Clutch Bracket
Figure 3
Clutch Bracket
Figure 4
Clutch Bracket