Draper FlexShade 2 설치 및 운영 지침

{카테고리_이름} Draper FlexShade 2에 대한 설치 및 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper FlexShade 2 2 페이지. With pocket headbox

페이지 인쇄

1 Read instructions through completely before proceeding.

2 Follow instructions carefully. Installation contrary to instructions invali-

dates warranty.

3 Pick up shade from ends only. Picking headbox up at other points will

damage case and may damage fabric.

4 Entire bottom of shade headbox should be unobstructed to permit

access to bottom panel for making electrical connections or servicing.

5 Shade should be installed level (using a carpenter's level).

6 Operating switch(es) packed separately in shade carton. Do not

discard with packing material.

7 Shade operates on 110-120V, 60 Hz. current.

NOTE: Shade has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Mounting Shade

Regardless of mounting method used, the following points apply:

1 Shade should be lifted into position only by the end mounting brackets.

Using both mounting holes in mounting brackets makes for a much

more stable installation. Never attempt to lift shade along its length.

2 Shade should be positively and securely supported so that vibration or

even abusive pulling will not weaken installation.

3 Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen. Installer must also insure that

wall or ceiling structure are of adequate strength. Supporting

hardware (chains, cables, rods, etc.) must be essentially vertical.

4 Entire bottom of pocket must be readily accessible after installation is

complete.

5 Front, back and top of pocket must be straight—not forced to warp or bow.

Adjust spreader bars to keep large cases from warping.

6 Do not use pocket to support adjacent sections of ceiling.

7 If optional ceiling flange trim kits are attached, use hardware provided.

8 If pocket is painted, slots on bottom of case should be shielded to protect

viewing surface from paint splatters or overspray.

Caution: Shade is shipped with motor wiring mounted to the headbox. Be

careful not to pull the wiring loose from the headbox while removing the

brackets—if wiring is loose, it could be damaged during shade operation. If

wiring does come loose, re-mount as it was.

9 Do not seal unit in ceiling until electrical connections have been made and

shade has been operated successfully.

Electrical Connections

Shade operates on 110-120V, 60 Hz. current.

Shade is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting shade to switch(es) and switch(es) to power supply

should be furnished by installer. Connections should be made in accordance

with attached wiring diagram, and wiring should comply with national and

local electrical codes. See Fig. 1 for internal view of wiring.

Shade roller removed for clarity

All operating switches should be "off" before power is connected.

Installation/Operating Instructions

FlexShade 2 with Pocket Headbox by Draper

Caution

Figure 1

Please Note: For low voltage wiring requirements, Draper recommends con-

sulting with a professional low voltage electrical contractor. It is very important

that shielded and stranded CAT 5 cable be used to prevent any electrical

interference.

When shade is first operated, be cautious! Cycle unit down and up several

times to confirm satisfactory operation.

Shade has been factory set and should not normally require further

adjustment. However, if you desire to change the "up" and "down" stopping

positions, proceed as follows:

CAUTION: Be sure all switches are in "off" position before adjusting

limit switches. Always be prepared to shut shade off manually when new

adjustment is being tested. Shade may be severely damaged if allowed to run

too far up or too far down.

ADJUSTING "FULLY UP" POSITION—Put a small screw driver in the groove

of the yellow button on the motor and press vertically until hearing a "click".

Raise the shade by pressing the "up" switch on unit. Press the "stop" switch

when the shade is at the desired position. Then press the yellow button on

motor until you hear a "click", then release.

ADJUSTING "FULLY DOWN" POSITION—Put a small screw driver in the

groove of the white button on the motor and press vertically until hearing a

"click". Lower the shade by pressing the "down" switch on unit. Press the

"stop" switch when the shade is at the desired position. Then press the white

button on motor until you hear a "click", then release.

AT NO TIME SHOULD SHADE BE UNROLLED ENOUGH TO EXPOSE ANY

PART OF SHADE ROLLER.

Please Note: The above instructions affect only the limits on the motors. For

adjustment procedures using Draper's IntelliFlex Control Systems, please

consult the installation information for the appropriate control.

suspending shade) by others.

Knockouts for electrical connections

(three per end) with plastic plugs

Removing/Replacing Roller

If there is not sufficient access above the ceiling to get to the mounting

brackets, you can use the knockouts located in the top of the case just below

the mounting bracket holes. To get to these holes, you will need to remove the

hole covers. You will also need to remove the shade motor/roller assembly.

These steps may require more than one person.

Removing Shade/Motor Assembly

1 Unplug motor from unit wiring (see Fig. 1).

2 Remove cotter pin from idler assembly.

3 Remove locking screw from motor retainer ring, then expand motor

retianer ring around the motor-end bracket (see Fig. 2).

4 The idler is spring-loaded. Push motor/roller assembly toward the idler

end. Remove motor from motor mount, then remove idler end.

5 Mount the case using mounting brackets. A long-handled driver will allow

you to access the bracket mounting holes through the knockouts.

Please see back page for dimensional diagrams of case, wiring dia-

grams and instructions on replacing the roller/roller/fabric assembly.

If you encounter any difficulties installing or servicing your FlexShade 2 with Pocket Headbox,

call your dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.

Operation

Adjustments

" threaded rod (for

Please note: Maximum

torque for tightening

screw is 5 lb-inches.

Figure 2