Draper LightBloc Zip 설치 지침 매뉴얼

{카테고리_이름} Draper LightBloc Zip에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper LightBloc Zip 6 페이지.
Draper LightBloc Zip에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (6 페이지)

페이지 인쇄

1 Inspect all boxes to make sure you have received the proper parts.

2 Open cartons lengthwise.

3 All hardware must be installed level. Shades must be level and square.

4 DO NOT wire motors in parallel without written permission from Draper.

5 Fasteners are not supplied by Draper. It is the responsibility of installer to

make sure that appropriate ones for the mounting surface are used. For Jamb

Mounting, Draper recommends the use of low profile head screws to allow the

"zippers" to easily pass through the Side Channels.

6 For installing units in recessed areas where there isn't room to mount the

Headbox to the Side Channels, please see note on page two.

7 LightBloc Zip is designed to operate only when the fabric panel is installed

vertically, perpendicular to the ground. Angled installations, where the side

channels are NOT installed vertically, may prevent the unit from closing.

9 DO NOT run down shade cloth outside of the Side Channels.

9 Please read the following installation guidelines thoroughly and follow

them carefully. Failure to do so may cause product to fall or otherwise

fail, and invalidates warranty.

Preparation for Installation

1 Make sure mounting surface is strong enough to hold the LightBloc Zip.

Please Note:

It is the responsibility of installer to

use appropriate fasteners for the mounting surface.

2 Verify unit measurements, and make sure it will

fit in the desired location.

Please Note: The Hembar does not retract into

the Headbox. This will need to be accounted for

if mounting over a swinging window or door.

3 Mounting brackets MUST be installed with a gap

of 1¾" (45mm) between the End Cap

and the Mounting Bracket edge (See Fig. 1).

Mark wall, jamb or ceiling.

4 Drill small starter holes (if necessary) in mounting surface.

*** If Installing Zip 127 Angled Headbox see page 3. ***

Mounting Headbox with Brackets - Wall Installation

Attaching Mounting Brackets

1 Attach mounting brackets to the wall using #10

flat head screws installed flush with bracket.

Be sure to use AT LEAST 2 of the top

mounting holes (See Fig. 2).

Figure (2)

2 Attach Headbox to brackets and tighten Set Screws (See Fig. 3).

3 You are now ready to mount the Side Channels (See Page 2).

Form LightBlocZip_Inst17

Installation Instructions

LightBloc

Caution

MOUNTING

BRACKET

1¾"

(45mm)

E N

C A

Figure (1)

Tighten Set Screws

Figure (3)

Printed in U.S.A.

Zip by Draper

™

Mounting Headbox - Permanently to Ceiling or Wall

1 Attaching Mounting Brackets to Headbox

Attach Mounting Brackets to the Headbox

as a spacer between the Headbox

and the wall.

Leave a 1¾" (45mm) gap

between End Cap and

Mounting Bracket

(See Fig. 4), and

tighten set screws.

Leave a

1¾" (45mm)

GAP for

Side-Channels

2 Removing Roller Assembly

A. Remove screws from

bottom of Headbox,

remove Fascia and

set aside.

B. Remove Quick

Release Pin from

Idler End of Roller

Assembly.

C. Remove Roller

Assembly, Idler End

first, and set aside.

3 Mounting to Ceiling / Wall

Using the mounting holes in the end caps as a guide (See Fig. 6), drill pilot

holes on both ends of the Headbox. Attach to mounting surface using

appropriate fasteners.

Please Note:

It is the

responsibility of installer to

use appropriate fasteners

for the mounting surface.

4 Once the Headbox is

secured to the mounting

surface, re-install

Roller Assembly*,

Quick Release Pin

and Fascia.

*Note: If there is no cable

exit provided, you must drill

one before re-installing Roller Assembly. See Cable Exit on Page 4.

5 You are now ready to mount the Side Channels (See Page 2).

If you encounter any difficulties installing or servicing your LightBloc Zip, call your

dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999, or fax 765-987-7142.

Figure (4)

Attach

Mounting Bracket

as spacer and

Tighten Set Screws

Figure (5)

REMOVE

FASCIA

REMOVE QUICK

REMOVE ROLLER ASSEMBLY

RELEASE PIN

Remove screws from

bottom of Headbox

CEILING

MOUNT HOLES

WALL

MOUNT HOLES

Figure (6)

Continued on next page