Draper Motorized FlexShade 사용 설명서 - 페이지 9

{카테고리_이름} Draper Motorized FlexShade에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper Motorized FlexShade 12 페이지. Motor operated window shades with several control options
Draper Motorized FlexShade에 대해서도 마찬가지입니다: 설치 및 작동 지침 (8 페이지)

페이지 인쇄

Motorized FlexShade

Section 7 - Attaching Fascia to Endcaps

Please Note:

- Endcaps must be installed the correct

distance apart for fascia to be properly

attached with full engagement.

STANDARD ROLL FASCIA

Place groove

along top of

fascia over

endcaps.

STANDARD ROLL FASCIA

STEP 1:

ENDCAP

Snap into

place.

Section 8 - Limit Switch Adjustments

Standard and Quiet Motors

Push Button Limits

1. Fully depress both limit switch push buttons, then

operate wall switch to make sure system works properly.

2. Raise shade to desired "up" stop position.

3. Set upper limit by depressing proper

4. Lower shade to desired "down" stop position.

5. Set lower limit by depressing proper

Screw-Type Limits

1. Determine which direction of fabric travel corresponds

with arrows on motor.

2. Operate shade to desired "down" stop position.

Set limit by turning proper socket toward

and

to raise it.

3. Operate shade to desired "up" stopping position. Set limit by

turning proper screw toward

Limit Switch Adjustments:

RS485 Motors:

See limit setting instructions

packaged with the RS485 Address/

Limit Setting Tool

(part# C156.241)

Section 9 - Electrical Connections

Shade operates on 110-120V, 60 Hz. current. Shade is shipped with internal wiring complete and control switch

cable lead. Longer lead can be substituted by removing two screws in motor end of roller, removing lead, plugging new lead in, and replacing screws. Wire to connect

shade to switch

and switch

(es)

Connections should be made in accordance with attached wiring diagram, and wiring should comply with national and local electrical codes. DO NOT wire motors in

parallel without written permission from Draper

All operating switches should be "off" before power is connected.

Please Note: For low-voltage wiring requirements, Draper recommends consulting with a professional low-voltage electrical contractor. It is very important that

shielded and stranded CAT 5 cable be used to prevent any electrical interference.

Please Note: A Draper Motor Test Cable

IMPORTANT: To reduce the risk of electric shock, equipment that features a grounding type attachment plug has a third

This plug will ONLY fit into a grounding type outlet. If the plug does not fit into the outlet, a qualified electrician must install the proper outlet.

DO NOT change the plug in any way.

DO NOT use an extension cord. If the power supply cord is too short, a qualified electrician must install an outlet near the drapery operator.

REVERSE ROLL FASCIA

STEP 2:

STEP 1:

REVERSE ROLL FASCIA

Slide endcap

STEP 1:

ENDCAP

onto fascia.

REVERSE ROLL FASCIA

STEP 1:

Clicks into place

STEP 2:

ENDCAP

Clicks into place

(All procedures shown are for Standard Roll. Invert orientation for Reverse Roll)

push button.

(back)

push button.

(front)

to lower limit,

to raise limit, and

to lower it.

RTS Motors:

See Radio Frequency Remote

Control Programming Instructions

(FS_MO_RFRC_ProgInst)

to power supply should be furnished by installer.

(es)

and M12 Pigtail

(Part# 503109)

(Coupled)

- Fascia is not fully seated

until it clicks into place

on both ends.

Hang fascia

on room side

STEP 2:

of endcap.

STEP 2:

Caution:

Be sure all switches are in "off"

position before adjusting limit

switches.

- Be prepared to shut off

manually while testing.

- Shade may be damaged by

running shade fabric down too

far to expose roller.

- If using a group control system,

each limit switch must be set

prior to connecting to system.

- Motor must be installed so limit

switches are pointed down.

IntelliFlex I/O Motors:

See limit setting instructions

packaged with the Motor Limit

Setting Tool

(part# C202.030)

are available for temporary power for testing and limit setting.

(Part# C107.089.60)

- Once in place, check for secure fit.

If not secure, use an appropriate

fastener

(not included)

Slide Clip to end of fascia, ensuring that

clip covers mounting bracket of endcaps.

STEP 2:

STEP 3:

R O

L L E

R O

L L E

S L

I D E

S L

I D E

ROOM SIDE

Tighten

set screw

with included

Hex Wrench.

PUSH BUTTON LIMITS

GLASS SIDE

ROOM SIDE

Front

Back

GLASS SIDE

Bottom View

SCREW-TYPE LIMITS

GLASS SIDE

ROOM SIDE

Front

Side View

Back

GLASS SIDE

Bottom View

fully boxed, and standardly supplied with a 6'

(es)

Screws

Side View

pin on the attachment plug.

(grounding)

page 9 of 12

STEP 3:

R O

A kit containing two

L L E

clips and a hex wrench

is supplied per

Reverse Roll

each piece

Fascia Clip Kit

of fascia.

Tighten

set screw

with included

Front

Tighten set-screw with

Hex Wrench.

included Hex Wrench.

Back

Standard right-hand

motor configuration shown

Bottom View

Front

Back

Side View

Standard right-hand

Bottom View

motor configuration shown

Screws

Side View

(1.8 m)