Bosch 46 HBN 44 설치 지침 매뉴얼 - 페이지 10

{카테고리_이름} Bosch 46 HBN 44에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 46 HBN 44 28 페이지. Electric built-in single & double oven
Bosch 46 HBN 44에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (48 페이지), 사용 및 관리 매뉴얼 (48 페이지), 설치 지침 매뉴얼 (28 페이지)

페이지 인쇄

ELECTRICAL SUPPLY

Before installing the oven have a qualified electri-

cian verify that your home is provided with ade-

quate electrical service and that the addition of

the oven will not overload the branch circuit on

which it is to be installed. A separate three-wire

or four-wire single phase, 240 Volt, 60 Hz., or a

208 Volt, 60 Hz. branch circuit is required.

Note: For use with 208 V, 60 Hz supply voltage

the wiring must be modified as shown in

Connecting to 208 Volt Circuit.

For hook-up of the oven you will need to have an

approved junction box installed where it will be

easily reached through the front of the cabinet

where the oven will be located. The oven has 3

feet of conduit. Allow two to three feet of slack in

the line so that the oven can be moved if servicing

is ever necessary. DO NOT shorten the flexible

conduit.

ELECTRICAL SHOCK HAZARD

•

The electrical power to the oven branch cir-

cuit must be shut off while line connections

are being made.

•

Do not use an extension cord with this ap-

pliance.

•

Electrical ground is required on this appli-

ance. The free end of the green wire (the

ground wire) must be connected to a suit-

able ground.

This wire must remain grounded to the

oven.

•

If cold water pipe is interrupted by plastic,

non-metallic gaskets, union connections or

other insulating materials, DO NOT use for

grounding.

•

DO NOT ground to a gas pipe.

•

DO NOT have a fuse in the NEUTRAL or

GROUNDING circuit. A fuse in the NEU-

TRAL or GROUNDING circuit could result

in an electrical shock.

•

Check with a qualified electrician if you are

in doubt as to whether the appliance is

properly grounded.

Failure to follow these instructions could re-

sult in serious injury or death.

WARNING

WIRING REQUIREMENTS

When making the wire connections, use the entire

length of the conduit provided (3 feet). The con-

duit must not be cut.

Before making connections make sure the power

is off and read and observe the following:

A separate three-wire or four wire, single

phase, 240 Volt, 60 Hz. or 208 Volt, 60 Hz

branch circuit is required for the oven.

The oven must be connected with COPPER

WIRE ONLY.

In the United States:

Wiring must conform to the National Electri-

cal Code, ANSI/NFPA No. 70 latest edition.

You can obtain a copy of the National Elec-

trical Code by writing:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

In Canada:

Wiring must conform to Canadian Electrical

Code C22.1- latest edition. You can obtain

copies of the Canadian Electrical Code by

writing:

Canadian Standards Association

178 Rexdale Boulevard

Rexdale (Toronto), Ontario, Canada

M9W 1R3

Wire size (COPPER WIRE ONLY) and con-

nections must be suitable for the rating of the

appliance per the National Electrical Code

requirements. The flexible armored cable ex-

tending from the oven should be connected

directly to the junction box.

The junction box should be located so as to

allow as much slack as possible between the

junction box and the oven so it can be moved

if servicing is ever required.

A U.L. listed conduit connector must be pro-

vided at each end of the power supply cable.