Bosch 800 Series 설치 매뉴얼 - 페이지 9

{카테고리_이름} Bosch 800 Series에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 800 Series 40 페이지. Built-in wall ovens
Bosch 800 Series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (24 페이지), 설치 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (12 페이지), 설치 매뉴얼 (23 페이지), 설치 매뉴얼 (28 페이지), 설치 매뉴얼 (32 페이지), 사용 설명서 (32 페이지), 설치 매뉴얼 (32 페이지), 빠른 시작 및 안전 매뉴얼 (7 페이지), 사용 및 관리 매뉴얼 (40 페이지), 설치 매뉴얼 (32 페이지), 설치 지침 매뉴얼 (40 페이지), 설치 매뉴얼 (48 페이지), 사용 및 관리 매뉴얼 (33 페이지), 사용 및 관리 매뉴얼 (49 페이지), 빠른 시작 매뉴얼 (7 페이지), 빠른 시작 및 안전 매뉴얼 (13 페이지), 설치 매뉴얼 (32 페이지), 서비스 매뉴얼 (36 페이지), 설치 지침 매뉴얼 (29 페이지), 사용 및 관리 매뉴얼 (24 페이지), 사용 및 관리 매뉴얼 (40 페이지), 설치 지침 매뉴얼 (28 페이지)

페이지 인쇄
Bosch 800 Series 설치 매뉴얼
Insert each of the LP gas orifices provided with this kit
4.
into the socket (using the small piece of foam tape to
assure a tight fit).
Note: The NGMP056UC and NGMP656UC models
have two orifices. The larger orifice should be installed
in the center port and the smaller orifice should be
installed in the port to the side.
Check to be sure the small piece of foam tape
A
used earlier is fitted to wrap against one side
of the socket.
When pressing the socket driver onto the ori-
B
fice, the tape will help the orifice fit more
snugly inside the socket. This will help prevent
the orifice from falling out of the socket during
insertion.
Step 3 - Replace the burners, burner caps
and grates
Replace the burners, burner caps and grates. Be sure
the grates are correctly placed and the rubber feet on the
grates engage the indents in the cooktop for proper
position.
WARNING
9
To prevent flare-ups, do not use the cooktop without
all burners, burner caps and burner grates properly
positioned.
WARNING
9
To prevent burns, do not touch burners, burner caps
or grates while hot. Turn the cooktop off and allow
the burners to cool.
The burner caps must be properly placed for the cooktop
to function properly. If the burner cap is not properly
placed, one or more of the following problems may
occur:
Burner flames are too high.
▯
Flames shoot out of burners.
▯
Stainless steel discolors.
▯
Burners do not ignite.
▯
Burner flames light unevenly.
▯
Burner emits gas odor.
▯
Burner Cap and Burner Base Placement
The small hole or cutout near the edge of the burner
▯
should line up with the igniter. Rotate the burner until
the igniter aligns with the electrode and gently lower it
on to the cup. The burner should not be able to rotate
when correctly placed on the cup. Pay special
attention to avoid damaging the igniter during
installation of the base. See Illustration below.
Once each base is located and resting evenly, place
▯
each burner cap on its correct burner base. See
Illustration.
Place burner cap gently on top of base so that the
▯
prongs of the burner base fit snugly into the groove of
the burner cap.
If the maintop is removed by a certified installer (for
▯
example to check electrical or piping connection) the
panhead screws that were removed must be re-
installed to ensure proper functionality of burners.
1
Placing Burner Caps and Bases
2
9