Bosch CBG633N 1 Series 사용 설명서 - 페이지 20
{카테고리_이름} Bosch CBG633N 1 Series에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch CBG633N 1 Series 48 페이지.
![Bosch CBG633N 1 Series 사용 설명서](/uploads/products/server2/1377467/1377467.jpg)
Cleaning
en
DCleaning
W ith good care and cleaning, your appliance will retain
C l e a n i n g
its appearance and remain fully functioning for a long
time to come. We will explain here how you should
correctly care for and clean your appliance.
Suitable cleaning agents
To ensure that the different surfaces are not damaged
by using the wrong cleaning agent, observe the
information in the table. Depending on the appliance
model, not all of the areas listed may be on/in your
appliance.
Caution!
Risk of surface damage
Do not use:
Harsh or abrasive cleaning agents,
■
Cleaning agents with a high alcohol content,
■
Hard scouring pads or cleaning sponges,
■
High-pressure cleaners or steam cleaners,
■
Special cleaners for cleaning the appliance while it is
■
hot.
Wash new sponge cloths thoroughly before use.
Highly recommended cleaning and care products
Tip:
can be purchased through the after-sales service.
Observe the respective manufacturer's instructions.
:
Warning – Risk of burns!
The appliance becomes very hot. Never touch the
interior surfaces of the cooking compartment or the
heating elements. Always allow the appliance to cool
down. Keep children at a safe distance.
Area
Cleaning
Appliance exterior
Stainless steel
Hot soapy water:
front
Clean with a dish cloth and then dry with a soft
cloth.
Remove flecks of limescale, grease, starch and
albumin (e.g. egg white) immediately. Corrosion
can form under such flecks.
Special stainless steel cleaning products suitable
for hot surfaces are available from our after-sales
service or from specialist retailers. Apply a very
thin layer of the cleaning product with a soft cloth.
Plastic
Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
Do not use glass cleaner or a glass scraper.
Painted surfaces
Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
Control panel
Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
Do not use glass cleaner or a glass scraper.
20
Door panels
Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
Do not use a glass scraper or a stainless steel
scouring pad.
Door handle
Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
If descaler comes into contact with the door han-
dle, wipe it off immediately. Otherwise, any stains
will not be able to be removed.
Appliance interior
Enamel surfaces
Observe the instructions for the surfaces of the
and self-cleaning
cooking compartment that follow the table.
surfaces
Glass cover for
Hot soapy water:
the interior light-
Clean with a dish cloth and then dry with a soft
ing
cloth.
If the cooking compartment is heavily soiled, use
oven cleaner.
Door seal
Hot soapy water:
Clean with a dish cloth.
Do not remove.
Do not scour.
Door cover
made from stainless steel:
Use stainless steel cleaner. Follow the manufac-
turers' instructions. Do not use stainless steel
care products.
made from plastic:
Clean using hot soapy water and a dish cloth. Dry
with a soft cloth. Do not use glass cleaner or a
glass scraper.
Remove the door cover for cleaning.
Rails
Hot soapy water:
Soak and clean with a dish cloth or brush.
Pull-out system
Hot soapy water:
Clean with a dish cloth or a brush.
Do not remove the lubricant while the pull-out rails
are pulled out – it is best to clean them when they
are pushed in. Do not clean in the dishwasher.
Accessories
Hot soapy water:
Soak and clean with a dish cloth or brush.
If there are heavy deposits of dirt, use a stainless
steel scouring pad.
--------
Notes
Slight differences in colour on the front of the
■
appliance are caused by the use of different
materials, such as glass, plastic and metal.
Shadows on the door panels, which look like
■
streaks, are caused by reflections made by the
interior lighting.
Enamel is baked on at very high temperatures.This
■
can cause some slight colour variation. This is
normal and does not affect operation.
The edges of thin trays cannot be completely
enamelled. As a result, these edges can be rough.
This does not impair the anti-corrosion protection.