Bosch CDG634AS0/68 사용 설명서 - 페이지 15
{카테고리_이름} Bosch CDG634AS0/68에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch CDG634AS0/68 36 페이지.
페이지 인쇄Use the rotary selector to set a later end time.
4.
The value is applied after a few seconds, or touch
the s field again. The end time is shown in the
display under the operating mode and temperature
or level.
Press the l Start/Stop button to start.
5.
The time at which the appliance will start is shown in
the display.
The appliance is in standby mode. When the appliance
starts, the cooking time counts down on the display.
Once the cooking time has elapsed, an audible signal
sounds. The appliance stops heating. The cooking time
00 m 00 s is shown on the display.
You can use the s field to set another cooking time, or
use the l Start/Stop button to continue the operation
without a cooking time.
When your dish is ready, switch the appliance off using
the ÿ On/Off button.
Changing and cancelling
To change the end time, interrupt the operation using
the l Start/Stop button and then touch the s field
twice. The end time is highlighted white and can be
changed using the rotary selector. Continue the
operation using the l Start/Stop button.
If you want to cancel the end time, reset the end time to
zero. You can start the set cooking time immediately
using the l Start/Stop button.
The end time can only be changed if the cooking
Note:
time has not elapsed. Otherwise the cooking result
would no longer be satisfactory.
Setting the timer
The timer runs alongside other settings. You can set it
at any time, even if the appliance is switched off. It has
its own audible signal so that you can tell whether it is
the timer or a cooking time which has elapsed.
Adjusting settings
The timer duration always starts at zero minutes.
The higher the value, the greater the time steps when
setting the timer.
The maximum setting is 24 hours.
Touch the t field.
1.
The symbol lights up red. On the display, the timer
duration is shown in white and in focus.
Set the timer duration using the rotary selector.
2.
Press the t field to start.
3.
After a few seconds, the timer also starts
Note:
automatically.
The timer duration counts down.
The timer remains visible on the display if the appliance
is switched off. When an operation is running, the
settings for this operation are shown in the foreground.
When you touch the t field, the timer duration is
displayed for a few seconds.
When the timer duration comes to an end, an audible
signal sounds and a note appears on the display. The
symbol is no longer lit up.
If the set timer duration relates to the appliance
Tip:
operation, use the cooking time. The time is visible in
the foreground and the appliance switches off
automatically.
Changing and cancelling
To change the timer duration, touch the t field. The
timer duration is displayed in white and in focus, and
can be changed by using the rotary selector.
If you want to cancel the timer, reset the timer duration
to zero. Once the change has been applied, the symbol
is no longer lit up.
PDishes
Y ou can use the "Dishes" operating mode to very easily
D i s h e s
prepare food. The appliance chooses the optimal
setting for you.
Applying settings for dishes
Using the rotary selector, go through all the dishes to
see which dishes are available in AutoPilot.
The cooking time depends on the dish and cannot be
changed.
Touch the % field.
1.
The first dish is highlighted in white in the display.
Turn the rotary selector to set the required dish.
2.
Use the l Start/Stop button to confirm.
3.
A note on accessories and shelf position is
displayed.
Press the l Start/Stop button to start.
4.
The appliance begins to heat up.
Once the cooking time has elapsed, an audible signal
sounds. The appliance stops heating.
Dishes
en
15