AirStage UTY-RSKG 운영 매뉴얼 - 페이지 2
{카테고리_이름} AirStage UTY-RSKG에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AirStage UTY-RSKG 2 페이지. Simple remote controller
AirStage UTY-RSKG에 대해서도 마찬가지입니다: 설치 매뉴얼 (9 페이지), 운영 매뉴얼 (2 페이지)
페이지 인쇄
START / STOP
Each press of the "
" button alternates operation and stop.
When operating, operation lamp (green)
FAN SPEED
Press the "
" button to select the fan speed while in
operation.
Fan speed indicator
NOTES
(AUTO)
(HIGH)
(Select the fan speed
automatically.)
OPERATION MODE
Press "
" button to select the operation mode while in operation.
NOTES
*
(AUTO)
(COOL)
(DRY)
*
A heat pump model that is not set up as an Administrative
Indoor Unit cannot operate in the AUTO modes.
** FAN cannot be selected for a heat pump model.
Refer to details in the Administrative Indoor Unit OPERATING TIPS.
*** Heating operation can not be performed in the
"COOLING-ONLY" models.
•
If the priority mode is set to "Priority on Administrative
Indoor Unit", the operating mode of other indoor units
except Administrative Indoor Unit will be controlled by
an Administrative Indoor Unit.
•
If the operating mode of Administrative Indoor Unit is set to "AUTO", "AUTO" is
displayed in addition to the indicator of current operating mode on other wired
remote controllers except Administrative Indoor Unit. In this case, operation of
other indoor units is controlled by the Administrative Indoor Unit.
Ex. : When operating mode of the Administrative Indoor
Unit is set to "AUTO" while air conditioning setting.
(The indication on other wired remote controllers except
Administrative Indoor Unit).
When Administrative Indoor Unit is set to "AUTO".
will light up.
(MED)
(LOW)
**
***
(FAN)
(HEAT)
OPERATION
Instructions on heating are not applicable for the "COOLING-ONLY" models.
NOTES
(1) When
is displayed, there are functions for which settings cannot be made.
When a button is pushed to change a restricted setting,
(2) When
is displayed, some operation are restricted. In such case, contact the administrator.
(3) During Automatic Defrosting operation and Oil Recovery operation,
the remote controller.
(4) • When "
" or "
" is indicated on the temperature indicator, it means under maintenance.
• When " " is indicated on the temperature indicator, anti freeze function is activated.
However, this function cannot be operated by the remote controller.
ERROR CODE
If an error occurs, the following indicator will be shown.
(" " will appear in the set room temperature indicator.)
If " " is displayed, immediately contact autho-
rized service personnel. Do not used the operation
as shown to the right if an error has occurred.
Occurrence of an error is indicated by the blinking of
operation lamp.
will flash.
(5) Preset values are displayed when the "
"
" button or "
" button, the "
while stopping.
(6) Mode indication blinks when inoperative setting of indoor unit is made.
(7) Blinking of the fan speed indicator means the timing for filter
cleaning of the indoor unit.
To erase indication, press the "
" button for more than 2 seconds.
TEMPERATURE
Press the "
" button or "
" button to set the room
temperature while in operation.
NOTES
Temperature setting range
AUTO • • • • • • • • • • • • • 18 to 30°C
COOL/DRY • • • • • • • • • 18 to 30°C
HEAT • • • • • • • • • • • • • 10 to 30°C
* Room temperatures as low as 10 to 15 °C cannot be set depending on the
model. (Heating)
* The temperature setting should be considered a standard value, and may
differ somewhat from the actual room temperature.
Faulty unit No.
(0-15, C0)
will be displayed on
" button, the
" button is pressed
Error code
Ex. Error code