Bosch GDS Professional 24 설치 지침 - 페이지 2
{카테고리_이름} Bosch GDS Professional 24에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch GDS Professional 24 5 페이지. 24" electric built-in single and double ovens
Bosch GDS Professional 24에 대해서도 마찬가지입니다: 원본 사용 설명서 (14 페이지)
페이지 인쇄
Product dimensions
Single oven
22-3/8" max.
recessed
width
27-1/2"
recessed
height
23-3/4"
23" max.
overall width
recessed
Cutout dimensions
24" min.
cabinet width
27-3/4"
min.
cutout
height
22-1/2"
cutout width
Single oven
undercounter
(without cooktop
installed above)
24" min.
cabinet width
27-3/4"
22-1/2"
min.
cutout
cutout
width
height
1-1/2"
min.
bottom of
cutout to
top of
cabinet
door
Single oven
Page 1
29" max.
overall
height
49-1/2"
recessed
height
23" max.
recessed
depth
49-3/4"
min.
cutout
height
1-1/2" min.
top of cutout
to underside
of countertop
1-1/2" min.
bottom of
cutout to top of
cabinet door
5-1/4" bottom of
cutout to floor
1" top of cutout
to bottom of
upper cabinet
door
cabinet
32"
bottom of
cutout to
floor
Double oven
22-3/8" max.
recessed width
51" max.
overall
height
23-3/4"
overall width
24" min.
cabinet
1" top of cutout
to bottom of
upper cabinet
door
22-1/2"
cutout
width
14-3/4"
bottom
of cutout
to floor
Double oven
23-1/4" min.
cutout depth
23" recessed
oven depth
oven
recessed
front
oven
Cabinet side view
Before you start...
Important: Observe all governing codes
and ordinances.
Proper installation is your responsibility.
Have a qualified technician install this oven.
Oven location should be away from strong draft
areas, such as windows, doors and strong
heating vents.
Cabinet opening dimensions that are shown
must be used. Given dimensions provide
minimum clearance.
Recessed installation area must provide
complete enclosure around the recessed portion
of the oven.
Electrical ground is required. See "Electrical
requirements."
Electrical supply junction box should be located
3 inches maximum below the support surface
when oven is installed in a wall cabinet. Drill a
1-inch minimum diameter hole in the right rear
or left rear corner of the support surface to pass
the appliance cable through to the junction box.
For undercounter installation, it is recommended
that the junction box be located in the adjacent
right or left cabinet. If installing the junction box
on rear wall behind oven, junction box must be
recessed and located in the upper or lower right
or left corner of cabinet.
Oven support surface MUST be solid, level and
flush with bottom of cabinet cutout.
It is the customer's responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is
adequate and in conformance with National
Electrical Code, ANSI/NFPA 70 — latest edition*,
and all local codes and ordinances.
Copies of the standards listed may be obtained from:
* National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
Tool needed:
Phillips
screwdriver
Parts supplied:
4 screws (double oven)
4 door removal pins
Note: If installing a single oven, you will need
only two screws and two door removal pins.