AirStage UTY-LNHU 설치 매뉴얼 - 페이지 3
{카테고리_이름} AirStage UTY-LNHU에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AirStage UTY-LNHU 10 페이지. Wireless
3. TURNING ON THE POWER
(1) Throw the circuit breakers for the indoor unit and outdoor unit.
(2) M a k e s u r e t h a t t h e o p e r a t i o n i n d i c a t o r l a m p a n d t i m e r
indicator lamp are slowly fl ashing alternately.
•
If the auto restart function has been set, the air conditioner will
operate with the settings which are immediately before the power
supply was turned off.
•
If an error has occurred, the lamps on the IR receiver unit will fl ash
quickly to indicate the error code. (Refer to the installation manual of
the indoor unit.)
4. INSTALLING THE REMOTE CONTROLLER
4.1. Load batteries (AAA/LR03/R03 x 2)
Take care to prevent infants from accidentally swallowing batteries.
When not using the Remote Controller for an extended period, remove
the batteries to avoid possible leakage and damage to the unit.
Dead batteries should be removed immediately and disposed of properly,
either in a battery collection receptacle or to the appropriate authority.
Do not attempt to recharge dry batteries.
Do not use rechargeable batteries.
If your skin, eyes or mouth contact the battery liquid, wash with enough
water immediately, and consult your doctor.
Note:
Use batteries in accordance with specifi ed standard only. Replace
discharged batteries with new units. Check the indicated poles and insert
from the minus pole.
To load the batteries, refer to the operating manual of the wireless remote
controller.
4.2. Installing the remote controller holder
Always use the accessories and specifi ed installation work parts. Not
using the specifi ed parts will cause units to fall off, electric shock, fi re,
etc.
Install at a place that can withstand the weight of the unit and install
positively so that the unit will not topple or fall.
When installing the controller holder take precautions to prevent access
by infants. It may cause an injury.
CAUTION
WARNING
Fixing of the holder cover with the screws in the standard parts may be
unsuitable if the wall or ceiling material is weak. If so, prepare screws
suitable for the wall or ceiling material, and fi x it.
Too tight fastening of screw may cause damage to the holder when fi xing
the holder of this unit.
Check carefully the installation location of this unit.
•
A place where the indoor unit receives signals clearly from the main unit.
•
A place where direct sunshine is avoided.
•
A place avoiding thermal radiation from heating devices, such as a stove.
Note:
•
Use the controller holder that is provided to avoid misplacing the remote
controller.
•
Out of the airfl ow from the air conditioner (cool or warm)
•
Out of the reach of small children.
•
If the air conditioner unit is installed in a room in which a fl uorescent light
on an electronic lighting control system (i.e., inverter light) is installed,
signal interference may occur.
•
If there is a fl uorescent light in the room in which the air conditioner is
to be installed, turn it on and make sure that the signal from the remote
controller can be received by the indoor unit from the intended installation
location.
•
When the signal receiving unit receives a signal from the remote
controller, a short beeping sound will be heard.
•
Install the remote controller holder to a wall, pillar, etc. with the screw.
•
After installing this unit, perform the test run to confi rm that the unit is
operating properly.
Then, explain the operation of this unit to the customer.
(1) Mount the Holder.
Screws
(M3 × 12)
(3) To remove the Remote Controller (when use at hand).
Slide up
Pull out
CAUTION
(2) Set the Remote Controller.
Insert
En-2