Bosch HBA41B2 1J Series 사용 설명서 - 페이지 10

{카테고리_이름} Bosch HBA41B2 1J Series에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch HBA41B2 1J Series 24 페이지.
Bosch HBA41B2 1J Series에 대해서도 마찬가지입니다: 사용 설명서 (24 페이지)

페이지 인쇄

Cancelling rapid heating

Set the function control knob to the zero setting. The oven

switches off.

Cleaning function

The cleaning function regenerates the self-cleaning surfaces

inside the oven.

The inside rear and side walls and ceiling of some ovens may

be lined with a highly porous ceramic lining. This lining absorbs

splashes produced during baking and roasting, dissolving them

while the oven is on. This cleaning system makes it possible to

regenerate self-cleaning surfaces that can not properly clean

themselves.

Before cleaning

Remove all pans and unsuitable accessories from inside the

oven.

Cleaning the oven's base and enamelled walls

Before programming the clean function, clean the surfaces

inside the oven that are not self-cleaning. Otherwise, stains will

appear that are impossible to remove.

Use a cleaning cloth and hot water with a little soap or vinegar.

If very dirty, use a fine steel scourer or a special oven cleaning

Care and cleaning

With good care and cleaning, your oven will remain clean and

fully-functioning for a long time to come. Here we will explain

how to maintain and clean your oven correctly.

Notes

Slight differences in the colours on the front of the oven are

■

caused by the use of different materials, such as glass,

plastic and metal.

Shadows on the door panel which look like streaks, are

■

caused by reflections made by the oven light.

Enamel is baked on at very high temperatures. This can

■

cause some slight colour variations. This is normal and does

not affect their function. The edges of thin trays cannot be

completely enamelled. As a result, these edges can be

rough. This will not impair the anti-corrosion protection.

Cleaning agents

To ensure that the different surfaces are not damaged by using

the wrong type of cleaning agent, observe the information in the

table. Do not use

harsh or abrasive cleaning agents,

■

cleaning agents with a high concentration of alcohol,

■

hard scouring pads or sponges,

■

high-pressure cleaners or steam cleaners.

■

product. These must only be used when the oven interior is

cold. Do not use metal scourers or special oven cleaning

products on self-cleaning surfaces.

Setting

Cleaning takes about an hour.

Turn the control knob to the hot air function

Turn the temperature knob to

After one hour, turn off the control knob.

To cancel cleaning

Turn the function control knob to the

After cleaning

Once the inside of the oven has cooled, clean the ash remains

from the self-cleaning surfaces using a damp cloth.

Wash new sponge cloths thoroughly before use.

Area

Cleaning agents

Control panel

Hot soapy water:

Clean with a dish cloth and dry with a soft

cloth. Do not use glass cleaners or glass

scrapers.

Stainless steel

Hot soapy water:

Clean with a dish cloth and dry with a soft

cloth. Remove traces of limescale, grease,

starch and albumin (e.g. egg white) immedi-

ately. Corrosion can form under such resi-

dues.

Special stainless steel cleaning products

suitable for hot surfaces are available from

our after-sales service or from specialist

retailers. Apply a very thin layer of the

cleaning product with a soft cloth.

Door panels

Glass cleaner:

Clean with a soft cloth. Do not use a glass

scraper.

Glass cover for

Hot soapy water:

the oven light

Clean with a dish cloth.

Seal

Hot soapy water:

Do not remove.

Clean with a dish cloth. Do not scour.

Rails

Hot soapy water:

Soak and clean with a dish cloth or brush.

Telescopic

Hot soapy water:

shelves

Clean with a dish cloth or a brush.

Do not remove the lubricant while the pull-

out rails are pulled out – it is best to clean

them when they are inserted. Do not soak

or clean in the dishwasher.

Accessories

Hot soapy water:

Soak and clean with a dish cloth or brush.

setting.