Alemlube S Series 소유자 기술 매뉴얼
{카테고리_이름} Alemlube S Series에 대한 소유자 기술 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Alemlube S Series 2 페이지. Oil hose reel
Alemlube S Series에 대해서도 마찬가지입니다: 소유자 매뉴얼 (2 페이지), 소유자 기술 매뉴얼 (2 페이지)
OWNER'S TECHNICAL MANUAL
Description
With covers manufactured from high quality impact resistant and UV stabilised polypropylene and a positive latching mechanism that
automatically locks hose at the desired length, the new S Series of plastic hose reels from Alemlube will provide you with a reliable
& cost effective means of storing and retrieving hose assemblies in your workshop or garden. The reels can be floor, ceiling or wall
mounted & the detachable mounting bracket facilitates ease of reel mounting & storage.
Specifications
Uses/Pressure
Air and Water. Max. operating pressure: Air Reels: 290 psi
Hose Lengths
SA300 – 18m x 10mm ID hose. SA400 – 15m x 12mm ID hose.
Materials
Plastic covers, steel spring & Buna "N" seals
Pressure
SA300, SA400 – 290 psi (20 bar)
Weight/Dimensions
10kg / 490mm (L) x 448mm (H) x 228mm (W)
SA300 – 1/4" BSPT(f)/1/4" BSPT(m)
Inlet/Outlet
SA400 – 1/2" BSPT(f)/1/2" BSPT(m)
Working Temp
0°C– 50°C
Installation Of Reel
1 For overhead ceiling mounting: install reel at most, 3 metres
above the floor.
2 You will need to purchase appropriate hardware for the
mounting of your new reel.
3 The reel base has four 7mm (11/16") drilled holes for
mounting on a suitable flat surface. Figure 2 is a
template showing the correct location of the 4 mounting
holes in the base.
4 Using the three holes in the base, mount the reel in the
desired location. Be sure to use appropriate hardware and to
tighten the reel securely to the mounting location.
5 Apply Teflon tape or pipe sealant to the outlet fitting on the
hose & then attach to desired tool or nozzle. Check
connection for any leakage & check the reel for correct
operation. See operation section. If hose stop adjustment is
required, pull hose from reel and allow the reel to latch at the
desired length. Loosen hose stop bolts and slide hose stop to
a position close to the hose guide. Tighten hose stop bolts
and unlatch the reel.
Operation
1 Check your S Series reel for correct operation by slowly pulling out the hose.
A clicking noise will be heard every half revolution of the drum.
2 Latching mode switch, when your S Series reel is in free run state, pull out
the hose and allow it to retract after hearing the first, second or third click.
3 To unlatch the reel, slowly pull out the hose until the clicking noise stops, and
then let the hose retract unitl the hose stop rests against the hose guide.
4 NOTE: To avoid damage to your S Series reel, always hold onto the hose while it is rewinding. Periodically check the hose
condition for wear or damage and check the swivel fitting for leakage. Replace any worn, damaged or leaking parts.
Warning
1 Make sure incoming line pressure does not exceed the rated operating pressure for your model hose reel.
2 Use proper eye protection when assembling and using the hose reel.
3 Use soap and water when checking for leaks.
4 Keep children away from the work area.
NSW
QLD/PNG
TEL: (02) 9939 0711
TEL: (07) 3204 9166
FAX: (02) 9939 0411
FAX: (07) 3204 1224
Visit our website at
All manuals and user guides at all-guides.com
S Series Hose Reels
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
www.alemlube.com.au
Water Reel: 145 psi
WA
SA/NT
TEL: (08) 9209 3066
TEL: (08) 8241 7111
FAX: (08) 9209 3933
FAX: (08) 8241 7011
or
www.alemlube.co.nz
SA300
SA400
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008