Alemlube F20060 소유자 기술 매뉴얼

{카테고리_이름} Alemlube F20060에 대한 소유자 기술 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Alemlube F20060 2 페이지. Bi-lobe refuelling drum pump

Description

The F20060 is a high volume, manually operated, rotary action drum pump that delivers up to 100 L/min. It is designed for the

refuelling of both on and off road vehicles and large machinery. The simple design of the F20060 allows easy servicing if required.

The pump comes complete with delivery hose and includes a replaceable foot filter. * PLEASE NOTE: OIL GEARS BEFORE USE

(SAE 30 oil is recommended for this purpose).

Specifications

Uses

Discharge Quantity

Materials

Weight

Size

Operating instructions

1 Oil Gears Before Use

Before using the F20060 high volume rotary refuelling pump,

make sure that you fill the gear cover with oil. Fill with SAE 30 oil

or equivalent to the reference line through the lubrication bolt hole

(as indicated on the diagram). Inspect periodically.

2 Revolution Direction

The handle turns in a clockwise direction and the pump discharges

one litre per one revolution of the handle.

3 Filter

A filter of #80 mesh polyethylene net is supplied as standard on the

pump and is located at the bottom of the suction pipe. Rotating the

handle and therefore operating the pump may become harder if

the filter is clogged with impurities that may have been filtered

out of the fuel or low viscosity oil. It is recommended that you

remove the filter periodically and clean it with kerosene.

4 Cautions

Suitable liquids include most low viscosity liquids such as diesel,

unleaded petrol, kerosene and low viscosity oils. Although the pump

can be used to pump other liquids of high viscosity, the pump becomes

harder to operate and doing so will shorten the life of the pump & may

void the warranty.

Do not use this pump for any solvent or chemical transfer as these liquids will

dissolve the Buna N seals and gaskets, etc. (Use the 301-A, 401-A, 733 or 933

for solvents).

Please note when pumping fuels like kerosene, petrol or diesel, these products

tend to "dry out" the internals of the pump causing parts "to stick" and the

pump not to prime and dispense. To stop this from happening and to

increase the working life of your pump, we recommend that you lubricate the

gears of the pump by dropping a few drops of oil into the pump body by

taking off suction pipe F20060-35 & lubricating at this opening. After

undertaking lubrication of the pump in such a manner, please rotate the

handle a few times.

Do not pump liquids containing dirt or particles such as waste oil. Strained liquids

may block the filter, preventing discharge, which can damage the pump interior or

cause other problems.

NOTE: We recommend that the pump is inspected for any damaged twice a

year and that the oil inside the pump head is replaced every 12 months.

NSW/ACT

TEL: (02) 9677 1555

FAX: (02) 9675 1155

OWNER'S TECHNICAL MANUAL

EL SERIES

F20060 Bi-lobe Refuelling Drum Pump

Diesel and low viscosity oils up to SAE 30

1L per rotation / 100 L/min

Cast Aluminium, Buna N Seals

7.0kg

Suction pipe: 32mm ID x 1m

Delivery hose: 25mm ID x 2.2m

QLD/PNG

VIC/TAS

TEL: (07) 3204 9166

TEL: (03) 8787 8288

FAX: (07) 3204 1224

FAX: (03) 8787 8266

Visit our website at

www.alemlube.com.au

SA/NT

TEL: (08) 9302 4199

TEL: (08) 8241 7111

FAX: (08) 9303 2095

FAX: (08) 8241 7011

www.alemlube.co.nz

TEL: (64) 9 447 1007

FAX: (64) 9 447 1008