Draytek VigorAP 700 빠른 시작 매뉴얼

{카테고리_이름} Draytek VigorAP 700에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Draytek VigorAP 700 1 페이지. V2
Draytek VigorAP 700에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (1 페이지)

페이지 인쇄
Draytek VigorAP 700 빠른 시작 매뉴얼
V
i
g
V
i
g
V
i
g
!!!
This document is offered for VigorAP 700 v2 only. For the
latest and correct firmware, please visit the DrayTek web site.
Using the wrong firmware could make your unit inoperable.
Installing Your VigorAP 700
Package Content
VigorAP 700
Quick Start
Guide
CD
Antenna
Power Adapter
1.
Connect VigorAP 700 to ADSL modem, router, or
switch/hub in your network through the LAN port of the
access point by Ethernet cable.
2.
Connect a computer to ADSL modem, router, or
switch/hub. Make sure the subnet IP address of the PC is
the same as VigorAP 700, e.g., 192.168.1.X.
3.
Connect the A/C power adapter to the wall socket, and then
connect it to the PWR connector of the access point. Power
on VigorAP and check all LEDs on the front panel. PWR
LED should be steadily on, LAN LEDs should be on if the
access point is correctly connected to the ADSL modem,
router or switch/hub.

Web Configuration

To connect to VigorAP 700, the wireless client(s) must use the same SSID as VigorAP 700. The VigorAP 700 default settings are listed as
follows:
Default Settings
Wireless Access Point
Device Name
VigorAP 700
SSID
DrayTek
Channel Number
11
IP Address
192.168.1.2
Login Username /
Admin /
Password
1234
o
r
A
P
7
0
0
o
r
A
P
7
0
0
o
r
A
P
7
0
0
Version: 1.21 Date: 27/04/2011
1. Start your computer.
2. Open a web browser on your PC and
type http://192.168.1.2. A pop-up
window will open to ask for username
and password. Type the default values
stated on the window and click OK for
next screen.
3. The Main Screen will pop up. Please
set the wireless LAN settings for using
wireless function.
4. For detailed configuration of
VigorAP 700, please refer to User's
Guide.
Q
u
i
c
k
S
t
a
Q
u
i
c
k
S
t
a
Q
u
i
c
k
S
t
a
LED
Status
PWR
On
Off
WLAN
On
Blinking
LAN
On
Off
Blinking
Interface
Reset/WPS
LAN
r
t
G
u
i
d
e
r
t
G
u
i
d
e
r
t
G
u
i
d
e
Explanation
The device is powered on.
The device is powered off.
WPS mode is enabled.
Data is transmitting (sending/receiving).
LAN is connected
LAN is disconnected.
Data is transmitting (sending/receiving).
Description
Restore the default settings.
Usage: Turn on the VigorAP 700. Press the
button and keep for more than 10 seconds.
Then the AP will restart with the factory
default configuration.
Press the button and keep it less than 5
seconds, the WPS connection will be
enabled.
Connecter for local networked devices.
Connecter for a power adapter.