Drayton miGenie Wish 2 T724R 설치 매뉴얼

{카테고리_이름} Drayton miGenie Wish 2 T724R에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Drayton miGenie Wish 2 T724R 2 페이지.

페이지 인쇄

Drayton

Step 1: Mounting the Wall-plate

! IMPORTANT:

Wireless Packs

Installation must only be carried out by a

qualified electrician or heating engineer.

Make sure mains input has a 3 amp fuse.

Single Channel : miGenie Wish 1 T714R

! CAUTION! Before installation, make sure the

Dual Channel: miGenie Wish 2 T724R

mains supply is switched off!

Multi Channel: miGenie Wish 3 T744R

Technical Helpline: 0333 7000 622

Website: www.draytoncontrols.co.uk

www.mi-genie.co.uk

E-mail: [email protected]

@DraytonControls

/DraytonControls

401 Southway Drive

Plymouth

PL6 6QT

United Kingdom

EU Design Regs:- 002180638-1/2/3

Installer Guide 06490211001 IssE

INSTALLATION Guide

Step 3: continued...

Step 4: Signal Strength

→

How to replace the batteries

The miGenie thermostat(s) & miGenie gateway are

pre-bound to the miGenie controller in the factory so

they just need to be positioned in the best place for

Remove the battery covers as shown. Replace the

wireless communication. To help with this there is a

spent batteries with 2 x 1.5V IEC LR6 (AA) Alkaline

built in signal strength indicator, available in the Zone

batteries ensuring correct orientation. Replace the

battery covers pressing fully home.

Settings menu on the miGenie controller, as shown.

It is recommended that the signal strength is Good or

Very Good to ensure communication is maintained.

miGenie thermostat rear

The signal strength can also be seen on the miGenie

thermostat.

To enter the Signal Strength menu

• Press + & - for approx. 5 secs, then scroll (+/-) to show

10. ADV-SET,

Battery Covers:

• Press ( ) to enter the Advanced Settings menu,

Slide outwards

• Press +/- until 19 WIRELESS is shown,

to remove

• Press ( ) to enter the Wireless menu,

• Press +/- to show 21 SIG-LEVEL as shown,

• Press ( ) to see the current signal strength.

Battery Handling

Batteries, rechargeable or not, should not be disposed

of into ordinary household waste. Instead, they must be

recycled properly to protect the environment and cut

down the waste of precious resources.

If POOR is displayed, look for a better location

Your local waste management authority can supply

If NO SIGNAL is displayed, try connecting again with

details concerning the proper disposal of batteries.

the room unit in a different position. To exit, press + &

In compliance with the EU Directive 2006/66/EC, the

- keys for approx. 5 seconds. If there is no key pressed

button cell battery located on the printed circuit board

for 2 minutes, the menu will be exited automatically.

inside the product, can be removed at the end of the

product life, by professional personnel only.

Option 1: Fitting a new wall-plate

The ideal location is 1.2m above

floor level, with reasonable

lighting, good access, no

condensation, no extremes of

temperature and a supporting

surface that fully covers the

back of the unit. Position with

70mm clearance to the right,

25mm above and sufficient room

to access the securing screws

underneath. Fix, with terminals

at the top, either direct to a flat

wall using wall plugs and No. 6 x

1" (25mm) woodscrews, or on a

flush mounting single conduit box

type UA1 (BS4662) using M3.5 x

14 bolts. Check the 3A fuse, and

switch on the mains.

Option 2: Using an existing

industry standard wall-plate

Loosen the securing screws

on the old programmer and

unplug it. Check that there is

70mm clearance to the right of

the wall-plate and 25mm above

it. Check the wiring diagram for

your product model to compare

terminals and, if necessary,

change the wiring of the wall-

plate to suit. Now fit the miGenie

controller into the wall-plate and

tighten the securing screws.

! DO NOT use a surface mounting box

Check the 3A fuse, and switch on

the mains.

Step 5: Mounting Options

→

Once the best position has been identified, the

miGenie thermostat should be fixed to the wall using

the wall bracket as shown.

Care should be taken to mount the miGenie thermostat

in a position which is not subject to direct sunlight or

draughts. Preferably it should be mounted on an inside

wall about 1.2m (4ft) above the floor in a position where

it can respond to room temperature but away from the

direct influence of radiators or other appliances giving

off heat.

NB. miGenie thermostat can also be positioned using

the table stand included.

eg.

It has to be placed in a location where it will be able to

control the room temperature.

Step 2: Wiring

→

Single Channel:

Dual Channel:

miGenie T714R

miGenie T724R

Connect the wiring as shown above.

T714R only: Note that the output contacts are

voltage-free, so power needs to be put on to

Terminal 1 either by linking from Terminal L or

from a separate supply with a 3A fuse.

Step 6: Install the miGenie Gateway & miGenie app

→

Location & Wiring

The miGenie gateway is designed to be placed

on a flat surface and should be located next to the

customer's internet router. A short ethernet cable is

provided to connect the miGenie gateway to a spare

LAN port on the back of the internet router (see

image below).

WAN

LAN

The miGenie gateway is powered from a standard

mains wall socket using the supplied adaptor plug.

1.2m

Step 3:

miGenie Thermostats

- Checking the batteries

How do I know when to change

the batteries?

When the batteries start to run low a battery icon

will flash in the display, to indicate "low battery"

during this time the miGenie thermostat will function

normally. Please replace batteries with 2 x 1.5V

IEC LR6 (AA) Alkaline batteries. When the battery

icon alone is shown in the display, the batteries are

completely exhausted and the miGenie thermostat

will cease to function (see below).

Re-activate by replacing the batteries.

Ch1 Ch2 Ch3 Ch4

Multi Channel:

miGenie T744R

! IMPORTANT:

Always switch off the mains before removing

the miGenie controller and never fit it to a live

wall-plate!

Status

Creating a User Account

The miGenie gateway reports status information

Note: You can only create a User Account when your

on the LED located on the rear of the product.

miGenie Wireless Pack has been fully installed.

An overview of the status information is given in the

table below:

You will first need to download the Drayton miGenie

app for your smartphone or tablet which is available

from the App Store or Google Play.

LED State

Activity

(During Setup)

Cycling through Red,

The miGenie gateway is attempting

Amber, Green

to bind to a miGenie Controller.

Can be started manually by

pressing and holding the gateway

button for 5 seconds.

Off

Indicates that either;

The app guides you through the registration process

- the miGenie gateway is not

which connects your miGenie system to your e-mail

connected to the miGenie controller.

address. During this process you will be asked to

press the button on the back of the miGenie gateway

- the miGenie gateway has not been

which will flash green until the connection is made.

registered with an internet account

A verification e-mail will be sent to you to confirm

and app.

your e-mail address before the app can be used.

Green flashing every

This occurs when the button on the

1 second

rear of the gateway is pressed. The

miGenie gateway is attempting to

connect to a miGenie app via the

internet. This mode will time out

after 5 minutes.

LED State (During

Activity

normal use)

Green

Indicates 'all OK' – the gateway is

connected to the miGenie controller

and internet control is available.

Solid Red

No RF signal – the device should

be relocated closer to the miGenie

controller.

Solid Amber

No internet connection – check the

status of the local internet router

and all cabling.

Once the gateway has been registered the system

is ready to control your heating and hot water.

To control your miGenie system from additional

smartphones or tablets simply download and install

the app and login using the same e-mail address

and password.

→