Bosch 2-26 DRE 원본 사용 설명서 - 페이지 9

{카테고리_이름} Bosch 2-26 DRE에 대한 원본 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 2-26 DRE 15 페이지. Gbh professional
Bosch 2-26 DRE에 대해서도 마찬가지입니다: 원본 사용 설명서 (27 페이지), 원본 사용 설명서 (13 페이지)

페이지 인쇄

Declaration of Conformity

We declare under our sole responsibility that

the product described under "Technical Data" is

in conformity with the following standards or

standardization documents: EN 60745 accord-

ing to the provisions of the directives

2004/108/EC, 98/37/EC (until Dec. 28, 2009),

2006/42/EC (from Dec. 29, 2009 on).

Technical file at:

Robert Bosch GmbH, PT/ESC,

D-70745 Leinfelden-Echterdingen

Dr. Egbert Schneider

Senior Vice President

Engineering

26.10.2007, Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

Assembly

Before any work on the machine itself, pull

the mains plug.

Auxiliary Handle

Operate your machine only with the auxiliary

handle 14.

Rotating the Auxiliary Handle (see figure A)

The auxiliary handle 14 can be set to any position

for a secure and low-fatigue working posture.

Turn the bottom part of the auxiliary handle 14

in counterclockwise direction and swivel the

auxiliary handle 14 to the desired position. Then

retighten the bottom part of the auxiliary handle

14 by turning in clockwise direction.

Pay attention that the clamping band of the

auxiliary handle is positioned in the groove on

the housing as intended for.

Adjusting the Drilling Depth (see figure B)

The required drilling depth X can be set with the

depth stop 13.

Press the button for the depth stop adjustment

12 and insert the depth stop into the auxiliary

handle 14.

Bosch Power Tools

Dr. Eckerhard Strötgen

Head of Product

Certification

The knurled surface of the depth stop 13 must

face downward.

Insert the SDS-plus drilling tool to the stop into

the SDS-plus tool holder 3. Otherwise, the mov-

ability of the SDS-plus drilling tool can lead to

incorrect adjustment of the drilling depth.

Pull out the depth stop until the distance be-

tween the tip of the drill bit and the tip of the

depth stop correspond with the desired drilling

depth X.

Selecting Drill Chucks and Tools

For hammer drilling and chiselling, SDS-plus

tools are required that are inserted in the SDS-

plus drill chuck.

For drilling without impact in wood, metal, ce-

ramic and plastic as well as for screwdriving and

thread cutting, tools without SDS-plus are used

(e.g., drills with cylindrical shank). For these

tools, a keyless chuck or a key type drill chuck

are required.

GBH 2-26 DFR: The SDS-plus quick change

chuck 2 can easily be replaced against the quick

change keyless chuck 1 provided.

Changing the Key Type Drill Chuck

(GBH 2-26 E/RE/DE/DRE)

To work with tools without SDS-plus (e.g., drills

with cylindrical shank), a suitable drill chuck

must be mounted (key type drill chuck or key-

less chuck, accessories).

Mounting the Key Type Drill Chuck

(see figure C)

Screw the SDS-plus adapter shank 19 into a key

type drill chuck 18. Secure the key type drill

chuck 18 with the securing screw 17. Please

observe that the securing screw has a left-

hand thread.

Inserting the Key Type Drill Chuck

(see figure C)

Clean the shank end of the adapter shank and

apply a light coat of grease.

Insert the key type drill chuck with the adapter

shank into the tool holder with a turning motion

until it automatically locks.

Check the locking effect by pulling the key type

drill chuck.

English | 21

1 619 929 726 | (14.11.07)