Bosch 7-115 사용 설명서 - 페이지 13

{카테고리_이름} Bosch 7-115에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 7-115 19 페이지.
Bosch 7-115에 대해서도 마찬가지입니다: 사용 설명서 (30 페이지), 사용 설명서 (43 페이지), 사용 설명서 (7 페이지), 원본 사용 설명서 (13 페이지)

페이지 인쇄

Technical data

Amoladora

Order number

Power [W]

127 V

Amperage [A]

220 V

No-load speed [min

]

–1

Grinding disk ø máx. [mm]

Grinding spindle threads*

Weight approx. (without accessories) [kg]

Protection class

* For Central America countries spindle thread ∅ 5/8"

Machine components

1 Spindle lock

2 On/ Off switch

3 Auxiliary handle

4 Grinder spinde

5 Protective Guard (GWS 6-115)

5.1 Screw (GWS 6-115)

6 Protective Guard (GWS 7-115)

6.1 Clamping lever (GWS 7-115)

7 Mounting flange

8 Roughing/cutting disc**

9 Clamping nut

quick clamping nut**

11 Pinm sponner

12 Hand protector**

13 Rubber sanding plate**

14 Sanding disc**

15 Round nut*

16 Auxiliary handle with vibration absorption**

**Not all of the accessories ilustrated or described are in-

cluded as standard delivery.

Intended use

The machine is intended for cutting, roughing and brushing

metal and stone materials without using water. For cutting

stone, a cutting guide is required.

Noise/vibration information

Measured values determined according to EN 50 144.

Typically the A-weighted noise levels of the product are: sound

pressure level: 88 dB (A); sound power level: 101 dB (A).

Wear hearing protection!

The typical weighted acceleration is 5.0 m/s

When using the auxiliary handle with vibration absorption,

the hand/arm vibration of the power tool used is typically

less than 2.5 m/s

For your safety

Working safely with this machine is possible only when

the operating and safety information are read completely

GWS 6-115

0 601 282 ...

670

5,6

3,2

11000

115 (4 1/2")

M 14

1,4

/ II

• Wear protective glasses and hearing protection.

• Wear protective gloves and sturdy shoes.

• When necessary, also wear an apron.

• The dust that is produced while working can be detri-

mental to health, inflammable or explosive. Suitable safe-

ty measures are required.

Examples: Some dusts are regarded as carcinogenic. Use

suitable dust/ chip extraction and wear a dust respirator.

• Dust from light alloys can burn or explode. Always keep

the work place clean, as blends of materials are particu-

larly dangerous.

• If the mains cable is damaged or cut through while work-

ing, do not touch the cable but immediately pull the mains

plug. Never use the machine with a damaged cable.

• Connect machines that are used in the open via a re-

sidual current device (RCD) with an actuating current of

30 mA maximum. Use only extension cables that are ap-

proved for outdoor use.

• When working with the machine, always hold it firmly with

both hands and provide for a secure stance.

• Always direct the cable to the rear away from the machine.

• Always switch the machine off and wait until it has come

to a standstill before placing it down.

• Insert the mains plug only when the machine is switched

off.

• For mains failure or when the main plug is pulled, unlock

the On/Off switch immediately and turn it to the off posi-

tion. This prevents uncontrolled restarting.

• The machine must be used only for dry cutting/ grinding.

• For all work with the machine, the auxiliary handle 3 must

be mounted.

• Hold the power tool only by the insulated gripping sur-

faces, when performing an operation where the cut-

ting tool may run into hidden wiring or its own cord.

GWS 7-115

0 601 800 ...

750

6,2

3,6

11000

115 (4 1/2")

M 14

1,7

/ II

and the instructions contained therein are

strictly followed. In addition, the general

safety notes on page 17 must be observed.

Before using for the first time, ask for a prac-

tical demonstration.