Electrolux DFB09JFCWD 사용 및 관리 매뉴얼 - 페이지 11

{카테고리_이름} Electrolux DFB09JFCWD에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Electrolux DFB09JFCWD 16 페이지. Freestanding dishwasher

페이지 인쇄

WARNING

Allow heating element to cool

before cleaning the interior.

Failure to do so can result in

burns.

Outside

—Occasionally wash with a mild nonabrasive

detergent and water. Rinse and dry.

Inside

—

The inside of the dishwasher is self-cleaning

with normal use.

To clean stainless steel wipe with the grains.

Use a Dishwasher Safe Detergent to help with the stains or

discolorations.

NEVER

use products that contain Chlorine Bleach or

Citric Acid.

NOTE

Hard water may cause lime deposit buildup on the interior

of the dishwasher.

Winterizing

A dishwasher left in an unheated place should be protected

from freezing. Have a qualified person do the following:

To Disconnect Service:

1. Turn off electrical power to the dishwasher at the supply

source by removing fuses or tripping circuit breaker.

2. Shut off water supply.

3. Place a pan under the inlet valve. Disconnect water line

from inlet valve and drain into pan.

4. Disconnect drain line from pump and drain water into

pan.

5. Reconnect the water inlet pipe to the water valve.

6. Remove the filter at the bottom of the tub and use a

sponge to soak up water in the sump.

To Restore Service:

1. Reconnect the water, drain, and electrical power supply.

2. Turn on water and electrical power supply.

3. Fill detergent dispenser and run dishwasher through a

NORMAL WASH Cycle.

4. Check connections to make sure they do not leak.

Cleaning the Filter

For optimum performance, your dishwasher is equipped

with a filter assembly featuring a main, coarse and

fine filter as shown in the drawing above. All food

fragments are removed from the dishwasher as water

passes through the filter assembly.

CARE AND CLEANING

Burn Hazard

Each part of the assembly should be cleaned often to

ensure that all food fragments are removed from the

dishes. To remove food fragments from the filter

assembly, the filters must be removed from the

dishwasher. To remove the filters, pull up on the edge

of the main filter. Next, rinse the main filter and fine

filter under running water. Cleaning with a brush may

also be necessary to remove any fragments trapped in

the filters. Once cleaning has been completed, simply

reassemble the filter as shown in the drawing below. To

ensure that the filter is fully seated, please press down

on the top of the main filter. Using the dishwasher

without a properly installed filter is not

recommended as it will reduce the cleaning

efficiency and may damage dishware.

Cleaning the Spray Arm

-The spray arm may need to be cleaned to insure that

there are no clogs to the spray arm jets and bearings

due to hard water chemicals.

-To remove the upper spray arm, hold the nut and

rotate the spray arm clockwise to remove it.

-To remove the lower spray arm, pull up on the

spray arm.

-To clean the spray arm use warm soapy water using a

soft brush to clean the jets and bearings.

-To replace the spray arm simply set the spray arm on

the shaft, take the retaining nut and turn it counter

clockwise until it has locked into place.

Cleaning the Door

To clean the edge around the door: Use a warm, damp

and soft cloth. To avoid penetration of water into the door

lock and electrical components, do not use a spray cleaner

of any kind.

WARNING

Abrasive agents and rough paper towels/cloths

should not used, as it may scratch or leave spots

on the stainless steel surface.

Coarse

Filter

Main

Filter

Fine

Filter